Quick Question!

Have you ever purchased from PartSelect.com before?

http://www.partselect.com/Schematics/LG/144941-1.gif
See part F013 in the diagram
http://www.partselect.com/Schematics/LG/144941-1.gif

Connector Assembly

PartSelect Number PS3524406

This dishwasher door hinge cable assembly connects the door to the spring. The door hinge cable and the door spring apply tension to the door to prevent it from dropping open too quickly. This part contains two plastic pieces which are approximately 2 inches in length by 3/4-inch in width, as well as a rope portion that measures approximately 8 inches in length. When beginning this repair, be sure to use caution when replacing the door hinge cable. The spring to which the door hinge cable attaches is under tension and could snap. This part is sold individually.

This part fixes the following symptoms:

  • Door latch failure.
  • Door won’t close.

Compare At

$10.32

You Save

$1.72

Your Price

$8.60
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 4 reviews What's this?
1-4 of 4
 

6 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Charles from DENNIS, MA

Dishwasher door became heavy and would fall to the floor if you didn't hold it up.

Removed mounting screws from sides of disher. Removed broken piece of connector assy still attached to hinge. Attached new connector assy to hinge then looped it around pulley with spring attached to opposite end. Need both hands to pull spring up to side of tub and connect it. I would suggest replacing both connector assemblies while you have the dishwasher pulled out. Push dishwasher back in and mount with screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers, Wrench (Adjustable)
Customer: David from NEW ORLEANS, LA

The hinge spring and/or connector assembly were not functioning, so the dishwasher door was extremely heavy.

Replacing the spring and connector assembly (the cord had frayed and broken) was easy and took only a matter of minutes to do. Wrestling the dishwasher in and out of its space under the counter was very difficult. Because my kitchen is compact, I had to move the refrigerator first, then disconnect the Romex cable and water lines from the dishwasher before I could pull it fully from under the counter. The side panels have screws in the front and the back, so the appliance had to be moved out until its back was exposed. But I got the job done and the door works just like a new one now!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Mark from IRWIN, PA

Supply line leaked afterwards. Had to replace it. Installers(home depot) had it rigged and now it is loose. Going to have to rig it somehow.

Loosened 3 screws and unhooked supply line and electric box and pulled it out.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Connector Assembly
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Allen from N LITTLE ROCK, AR

The dishwasher door would fall open when opening if it wasn't lowered slowly.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4