| |
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customergary from jefferson city MO
Broken microwave handle
I followed the instructions used by others about removing only a portion of the gasket - just enough to reveal the screws to remove. Five minutes later, I am finished.
THIS SITE IS FANTASTIC! THE SERVICE WAS FANTASTIC! I ordered the product on a Wednesday morning and the next day I received it - and that wasn't overnight shipping!
You get what you pay for - Parts Select is the best!
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRandy from Sandwich IL
Broken handle on door
Installed new handle with the two ordered screws. Everything fit. Quick repair. Though I believe the handle to be a little pricy.....when all is finished and all works properly one can overlook what ones feels is a little pricy. Also much cheaper than a entire new unit. Thanks for prompt delivery.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerMichael from Woodbridge VA
Handle on the microwave broke
The Parts select diagram and order ing process made it very easy to complete my repair job. After receiving my parts, I unscrewed the screws with a phillips driver. Then I popped out the handle. There is one tricky part - the screw is a bit too small for the existing whole and so I added a washer to fix this problem. I then slide in the new handle. Very easy!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerThomas from Pembroke Pines FL
Outer door frame was cracked and bottom of door handle was broken where the screw attaches to it.
Had already reverse engineered the door and it's parts so when the repair parts got here I already knew how the parts fit together. Took me 15 minutes max without instructions.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBrian from Piedmont AL
Broken door handle
1st I read what your other customers had done to repair their microwaves..And noticed the majority were women( I assumed).So not to be outdone,I pre-prepared my door for repair..I used the butterknife to open the seals around door(front and inside)removed bracket to locate were bottom screw sits,inserted screw and bracket,tightened a little to handle,inserted top screw to handle,tightened bottom screw all the way,closed all the seals,and tightened the top screw.New handle on in about 10 minutes.Thanks for your parts and the help I received form reading your other testimonials,
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJoellen from Castroville TX
Door handle broke off
Repair was super easy. All I had to do pop out the band on the inside of door, remove screws from previous handle. I put new handle in place and screwed back in and pushed the band back into place. Super easy and only took like 10 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerJames from Grayslake IL
Broken handle
It took all of 3 minutes to fix! Using a phillips screwdriver, unscrew top screw. I then used a putty knife to pry the seal ring open to reveal the bottom screw. I then used plyers to hold the broken plastic piece and removed the bottom screw. Hold the handle in place and screw in bottom screw, then snap seal ring back into place and replace top screw. I was shocked at how easy this was and also how fast the part was shipped. I was very pleased. Thank You!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRichard from Weston FL
Handle broke at attachment point
the top screw is plainly visible, the bottom screw is not and may give pause. If you remove the plastic ring, on the interior face of the door, it will give access to the bottom screw for the handle. While you have the handle off, remove the backing plate for the handle, on the front of the door by pulling outward, gently until it pops off. Then you can slide the front glass panel out and clean it. {CAUTION: do not spray any cleaner on the exposed glass with the mesh on it, it will be impossible to remove any liquid and will cause fogging when you replace the outer glass panel}. Replace clean glass panel, and handle backing plate, make sure it snaps in fully so the screw holes line up properly. Screw on new handle, replace plastic ring and you are back in business.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMike from Arcata CA
Broken bottom of door handle
unsrew top handle screw on inside of door, removed handle, slid handle plate out slid new one in (probably would not have had to replace this part but the part makes the job look better) removed snap in trim finish around window inside door, fished out old screw and broken plastic from handle, srewed new handle on, snapped trim back on and job was complete.
|
0 of 9 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomercHERYL from NASHVILLE TN
Melted stirrer cover, broken door handle
poped stirred cover off and replaced, easily.
where door handle had broken off I needed pliers to hold the plastic part of the door handle in order to unscrew the top of the handle from the door. I was unable to figure out how to get to the other screw and a friend completed the job for me. Wallah, new handle, looks like new, works perfectly. 1/3 the cost of replacement. Probably could have done without ordering one of the parts but it wasn't that much.
|