350976-1-S-Whirlpool-3952374           -Cam Driven Bearing
350976-1-S-Whirlpool-3952374           -Cam Driven Bearing 350976-2-S-Whirlpool-3952374           -Cam Driven Bearing

Cam Driven Bearing

PartSelect Number PS350976

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Unusual Noise.
  • Compare At

    $5.52
  • You Save

    $.92
  • Your Price

    $4.60
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Agitator Cam Kit

Part Number 334648

This kit included the cam, 4 dogs and bearing.

$7.62
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 4 reviews What's this?
1-4 of 4
 

15 of 19 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerRichard from Houston TX

Agitator would not spin

replaced the agitator cogs, bearing and the O-Ring. I looked all over Houston for these part, but found them on PartSelect. Had them in about 3 days. The repair only took about 30 minutes.

I saved a bunch of money!!
Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerBecky from Oskaloosa IA

Pump leaking, agitator not turning

First I went to this site and read what everyone had to say on leaking pumps. After finding the model number, I looked at the parts list, and found what parts I thought I would need. First I shut off the water and unpluged the washer Replacing the water pump was very easy after reading what other people had done. I pulled the washer out from the wall about 18 inches and tilted back on a 45 degree angle. The pump was now in plain sight and helt in with two slide clamps. Using a pair of plyers I remover both clamps from both hoses on the pump. By pushing to the outside of the pump I was able to remove both of the slide clamps. This allows the pump to be lifted out and off the motor shaft. As my washer had just started leaking " about one week" the pump slid off the shaft easy. There was no rust on shaft. Pump shaft has a slot in it so the pump can only go on one way. By reversing the way I removed the pump I was able to slide the new pump back onto the shaft and slide the slip clamps back over the pump. Replacing both hoses and both clamps. Now pump was in place. I pulled the washer away from the wall and slid back into place. That took care of the pump. For the top side I removed the top part of the agitator by pulling up and removing the part that holds the softner. Under this was a piece of plastic that I was able to lift out. Under that was a 12MM bolt with a rubber washer. Using a scoket set I removed the bolt and washer. Lifting up on the agitator it came right out. Pulling on each end of the agitator I was able to pull it apart. Inside was a large plastic washer and agitator directional cogs all in one piece. This piece just lifts up and off. I replaced the old piece with the new on and slid the two agitator back togeather. Setting the agitator back into the washer and put the 12mm bold and rubber washer back on. Then I put the plastic back on and set the top softer cup back in place. Snapping in the bleach dispenser was very easy, just shap into place. Pluging the washer back in, and turning back on the water I ran the washer with no clothes in it so I could check for leaks and make sure everthing was working. Repairing both parts took about 30 minutes and now the washer is like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerDavid from Stanton CA

Agitator began skipping and not moving through part of turn

Remove dispenser and barrier cap by hand to access cam assembly. Unbolted agitator assembly and pulled up firmly.
Able to access and replace cams. Before pulling out note how assembled and make sure to put back exactly the same. Singe person using this machine for 8 years. Poor design or quality of cams to fail so soon. Family of 5 would have been through this in a few years. For only 15 dollars definitely worthwhile repair. Parts arrived in days.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerJohn from East Hartford CT

Cogs were worn agator not working

Replaced Cogs agator works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4