Direct Drive Timer - 120V 60Hz

PartSelect Number PS350865

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not drain.
  • Compare At

    $145.99
  • You Save

    $24.33
  • Your Price

    $121.66
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 8 reviews What's this?
1-5 of 8
 

25 of 26 people found this instruction helpful

Parts Used

  • Direct Drive Timer - 120V 60Hz

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customermichael from deersville, OH

Washer would'nt cycle

remove two screws that hold down top piece that holds timer. [screws are at each end] pull the top peice foward[ toward front of washer] just about 1 inch,then flip it up so you can see back of timer,pull out black tab that holds timer knob [with the tweesers],remove knob and dial unplug the wiring remove the screw under timer knob raise clip on the side of timer so it will slide toward left side remove timer. reverse instructions to install. PS VERY IMPORTANT!!!!!MAKE SURE TO UNPLUG WASHER FIRST!!!!!!!!!!!!!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Direct Drive Timer - 120V 60Hz

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerCLIFFORD from HOT SPRINGS, AR

Some cycles would not run. Overheating odor.

Pulled washer out. Removed two top panel screws. Removed panel and removed timer. Reinstalled in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Agitator
  • Direct Drive Timer - 120V 60Hz

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerLinda from Enola, PA

Two fold: Agitator slipping, washer delays spin cycle untill lid is raised and dropped.

First repair was easy, remove center bolt, pull up on agitator and replace entire unit as one piece, replace bolt and liquid dispenser.

Second repair was more difficult in that I could not immediately find the release to remove timer control. After removing 5 screws unnecessaryily and studying unit more closely, tried prying up on little tab that has a "+" symbol on it that locks into a little hole. While holding up on that tab, slide timer unit sideways and unit falls out of washer panel. Simply slide the new unit in and it locks in place.

Also the directions to remove the knob were convienently printed on the orginal and replacement timer, but an ARROW pointing to the black tab on rear of the timer control would be helpful as I mistook the tab to be on the front side under the knob from studing the replacement and tried to pull the smaller inter knob off in order to push it in to release the larger outside knob portion in order to disconnect the timer. No harm done, eventually figured it out, but it still didn't fix the problem. As the washer will EVENTUALLY go in the spin cycle without picking up and dropping the lid, I'm assuming the lid switch is defective, although it appears to work otherwise. Any other possible soulutions appreciated.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Direct Drive Timer - 120V 60Hz

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMICHAEL from SALISBURY, MD

Washer would not agitate on normal setting but worked fine in other settings

Removed control knobs from front (small ones pull off leave large one in place for now). Remove 2 screws from back and remove 2 nutdrivers screws from back and lift top up. Remove large knob instructions on timer. Remove wiring plug and 2 screws from under the knob. Put new timer in place attach with screws. Plug wiring into timer. Re install the back with 4 screws. Once top in place re install the small knobs. Job complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used

  • Direct Drive Timer - 120V 60Hz

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Socket set

CustomerJoseph from Park Hill, OK

Would not spin or wash

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8