Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS3508101
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Some parts are hard to remove due to the inability to see the locking section of the fastener pin. The parts installation is self explanitory and no asdjustment is required, so beyond laying on the floor of a very small room and not being able to see some of the parts it's not bad.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I open the front, bottom side and everything was in front. I took out the plastic bolt and replace the absorber.
we removed the back panel of the washing machine, removed the old pins to the shocks and re-installed the shocks and pins. one pin gave us a hard time but it eventually went back in. the job was not to bad to do and now the wash machine is so quiet we can't even tell that it is on : ) this is our second repair that we have done on it ourselves, the first time we had to install a new control unit and spring and that was fairly easy also. who needs to spend alot of money to get their appliances repaired, you can easily do it yourself and save some money, plus we ordered the parts online and received them in about 2 days
The machine had the vibration for sometime but still worked so we left it alone until it stopped working. After some trouble shooting I discoverd 1. both lower shocks were broken off and the tub had hit the controller connector on the front right side so hard it had come loose. After plugging it back the washer worked again so I ordered the shock absorber kit from part select. I was able to install it by only removing the front lower cover. The pins took some effort to push back in but the parts fit perfectly and we are back in business. I had to use a large set of channel locks to force the pins back in as well as tapping them with a hammer.
I disconnected the water and the power first. I then removed the back of the machine. I also removed the 8 screws that hold the top and slid it forward to release it from the clips. I tilted the to up withour removing any wires. I then put a 2X4 accross the top and used #14 electrical wire to lift the drum up so I could attach the spring. It was easy to remove nad replace the shock absorbers once the release was pressed down on each pin. I did have to remove two screws that held a control panel top the base of the machine on the left lower corner. (looking from the back of the machine) to make it easier to remove and install that shock absorber. That part of the install was a breeze. The parts were all correct and arrived quickly.
Took off the front, and put a come along to rafters in garage to lift tub.Replaced shock asborers, waited for spring kit to be delivered, replacing all.Still isn't working need to check wiring to some compoments to see if a wire is broken.Hope to have it washing soon
It took more time to remove the screws on the back panel..remove back panel for better access..remove speed access box on lower left side ( 2 screws) to get access to nylon pegs, squeeze down on tabs and pull out . the little tabs are on the oppsite side of the split nylon...Replace shocks and nylon pegs..reattach speed access box.put the back on.....easy job, the new shocks are part metal, make sure the metal side of shocks go towards the tub...
My washer was leaking a bit on the left side, apparently from the place water enters from filler. I spent a bit of time inspecting that side of the thing and my jaw dropped when I finally saw the other side of the washer, the upper shock was broken off and the thing was not connected.I got my parts fast and removing the pins was a bit troublesome but some from access standpoint, but it wasn't hard - just took some extra effort and prying from the head side. Seems to run better with new shocks and no more leaking so far.
You could do the replacement by just removing the maintenance panel on the front, but removing the rear panel gives you more options for getting at the shocks. The front panel comes off with 2 screws, the back has a lot of screws holding it on, a cordless drill is the way to go.Prying on the head of the plastic bolt with a pair of needle-nosed pliers while pushing down on the tab seemed to work well. I did have to remove a small box that houses electronics to remove the one from the right side. While I was in there, I tightened up the numerous bolts that holds the drum shell together. Machine is much smoother now and no leaks.
I removed the bottom front panel ( 2 screws) and about 8- 10 inches back were the shock absorbers...the one on the left was easiest nothing in way I squeezed the locking tab and pushed the pin thru to remove the shock absorber...on the right side was a little tricky but got my arm round the drain hose and small pump and pushed that pin thru as well...installed new shocks and was good to go...I did call a local repair business here in belleview florida was told the shocks themselves would cost 37.00 for the pair and about 150 - 175 in labor...I paid 22.00 from parts select and did my own labor thanks for all the help...les
Followed the kit instructions to the letter. working around tight clearences was really the only thing to slow me down. The other posts tell the rest of the story better than I can.
Disconnected hoses, unplugged, took off top and back of washer. Removed the white plastic thingys that retained the broken shock absorbers. Installed the new ones, using a hammer and 1/2" copper pipe section to place white plastic thingys. Put back, top on. Reconnected hoses, plugged in. Presto!
I had read the instructions and suggestions on the site. The product arrived with a good set of instructions. I used the deep socket to push in the "catch" on the pins. Once the catch is depressed I pulled and twisted a bit to get the pins out. After I pulled both broken shocks out I replaced them as instructed. I did use a long wooden dowel to get the pins all the way in. Read the instructions and follow what they tell you and it'll be done in under 15 min.
First I removed two screws in front lower panel to access lower portion of washer machine. Use pilars to push four plastic pins from each end of two vibration/shock abs. Job was very easy and took less than 30 minutes to complete.
First I unplugged. The machine from the outlet then disconnected the two water supply lines from the machine. Next I removed the back panel to gain access to the bottom of the drum. Next I took a nut driver and used it to depress the little tab on the push pin that hold the bottom part of the strut on. After getting the pins out I replaced the old strut assembly withe the new one. I used the nut driver again. But this time I used it as a set tool. Place the nut driver on the end of the push pin and gently tap with a hammer. Until the pin is all the way in. After that I reversed the assembly process to put the machine back together.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.