Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Richard D - March 21, 2018
Verified Purchase
Oven control
I had to basically quess what was causing my oven to shut off after 20 minutes, first I replaced the temperature probe , that wasn’t it, thankfully I ordered the oven control also , that was the problem, would of been nice to get some directions took apart a lot more then I had to,the diagram on web site was useless, definitely not a job for weekend warrior, I’ve been a plumber for over 30 years and I say it was a 7 out of 10 for difficulty, but part worked so hopefully that’s the end of it.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 1.0 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Power control module stopped working suddenly; unable to use the oven.
Instructions on YouTube not available, so for me, this was trial and error. Unplug the range. Remove the stove top grates, burners, and using an 5-prong allen-like wrench (star shape), remove the fasteners attaching the burners to the stove top. Remove the screws behind the rear vent and completely remove the stainless steel vent fasci
... Read morea. Using a deep socket wrench, remove the nut associated with each burner unit. This is done from on top of the range after the grates, etc are removed. Tweezers may help here. There are 2 extra star-shaped fasteners attaching the R front burner to the burner unit, remove those. Carefully lift the top of the stove up, over the rear vents, and move it towards the back of the unit. An aluminum foil covered heat shield protects the power control unit for the oven at the front of the stove top. There are 2 bolts attaching it to the main unit, remove those. A white foam material is under the wiring leading to the power control unit. Carefully remove that. 4 screws hold the PCU in place, remove those. Carefully shimmy the PCU out from under the front part of the stove. Before installing the new PCU, I went through all the wire attachments making sure they came off easily; pulling them off and then replacing them. Using rubber gloves, I held the new PCU and systematically went through removing a wire connector from the old PCU, replacing it on the new PCU. This takes a bit of patience. Once attached, carefully replace the PCU and attach with the 4 screws. Then reverse these instructions to complete the job. I plugged the range in once the new PCU was attached with the 4 screws to determine if it worked. It did. It takes some doing to get the burners properly aligned so they can be tightened back down with the deep socket. I only hand tightened those nuts. Good luck!
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Loyda
November 29, 2017
My oven turns off, but I have to unplug the stove for a minute to get it started again. I think is the control board because since the day i bought this stove the control board was damaged. Do you have any suggestions?
For model number CGS980SEM1SS
Hello Loyda,
Thanks for your question. If all of the heating components are working properly, consider replacing the control board.
I hope this helps.
Was this helpful?
Thank you for voting!
Rich
March 11, 2018
My gas oven will start and run for about 20 minutes and then shuts off. It has to be unplugged and plugged back in to get any response, then the same thing happens every time and we cannot use the oven. Can you help?
For model number CGS980SEM1SS
Hello Rich,
Thanks for your question. This is most likely due to an issue with the temperature sensor. You may want to test the part with a multimeter to check for electrical continuity. Replace it if it shows no continuity.
I hope this helps.
