Lid Switch Assembly with Leads

PartSelect Number PS350434

Manufacturer Part Number 3949247
Manufactured by Whirlpool

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Timer will not advance.
  • Will not start.
  • Pumps but will not spin.
  • Will not agitate.
  • Will not fill with water.
  • Lid or door will not open.
  • Not draining.
  • Compare At

    $36.48
  • You Save

    $6.08
  • Your Price

    $30.40
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 160 reviews What's this?
151-160 of 160
 

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerDon from Tampa, FL

Washer did not eject water on some cycles. Timer seemed to be functioning, as far as I could tell

The video was really important to the ease of the repair. I shut off the water and electrical sources as directed. After disconnecting the timer/control assembly I disconnected the wiring connector between the main mechanism and the lid assembly. Next I released the clips that held the back of the washer to the "surround" that encases the main working parts of the washer. The surround was set aside for removal of the faulty switch. Next a careful cleaning of the entire washer removed years of dust,etc. The install of the new switch was the easiest part. The reassembly was not as easy as the disassembly had been. It was quite a trick to lift the surround back onto the frame and center it in the four pegs of the base. My wife got on the floor and directed me as to which way to move the surround. After a few tries it settled into place. I replaced the clips holding the back of the unit to the surround, connected the leads of the lid switch , Anchored the control unit to the base and after reconnecting the H2O and power lines, a successful test was performed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerSteve from Lake Forest CA

The cycle would stop

I watched the video & I knew I could replace the Lit Switch. I have never seen the inside of a washer before (I'm kinda a good handyman) we called "the guy" out to fix the machine but after watching the video I knew I could save the almost $200 "the guy" wanted to charge us! It was so easy. I order the part from your Co & 3 days it arrived as promised and the day ... Our washing machine work great! Two things, 1) saved a couple hundred & 2) I did it myself & that feels good. I have told several friends about your website! My next project, fixed the ice maker! Again, thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerRICK from WAUKEGAN IL

Switch broke off the lid, had to use screwdriver to keep switch activated

Watched the fix it video on Parts Selct Web Site, adapted the procedure to my washer.Removed 4 screws holding control panel down, the 2 clips, tilted case foward and replaced the switch, reversed the process and it was done. Tamara D from customer service was a big help in verifing the part since my numbers and Parts Select numbers were different.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerAnn from Chico CA

Wouldn't drain or spin.

I diagnosed the problem using the symptom list on the web site. The real give-away was that I could get the washer to start draining and spinning by poking my pinky finger into the hole on the right side to activate the bad lid switch (and keeping it there until the washer was completely drained). Once we got the new switch, we just followed the directions on the video. It was very straightforward. We saved at least $110 (The part plus shipping cost only $40. Sears had said they would charge $150 just to come over and look at the washer).

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDavid from Green River WY

Washer failed to work with lid closed.

Took off control panel, removed outer housing, replaced switch and cleaned entire unit, put it back together and it worked. I found out that the glue holding the old switch together had failed causing the two parts to separate, causing the failure.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerErvin J. from Dublin GA

Burned lid switch

I just replaced th old lid switch with the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJason from Pensacola FL

Washer would not drain and would not spin

1. Remove 2 screws and 2 bolts on the back of the Washer (Located on Top)

2. Lifted the Control Panel and moved it to the back of the washer (Leaning it backwards)

3. Removed 2 clips

4. Detached the Lid Switch electrical plug and pushed it down

5. Remove the lid Switch

6. Installation is the reverse

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customersusan from pompano beach FL

Water would not drain after wash cycle

I removed the two screws to the control panel, tilted it back, unpluged the old element, removed the two metal clips holding the outside housing then pulled it away from the washing machine. I then removed the two screws holding the element. I used a screw driver to lift the clasp holding the wires. Once the old element was removed I put in the new element. The hardest part was getting the housing back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerAdriana from Houston TX

Lid switch broke

Googled "Lid Switch Broken in Washer" with the model number of washer. There were several very helpful articles on how to do it. My boyfriend did it and said it was easy. The hardest part was putting everything back exactly where it belongs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 9 people found this instruction helpful

Parts Used

  • Lid Switch Assembly with Leads

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDiego from Ayden NC

The lid switch got broke.

I took off the broken switch, from underneath the lid support. Then I disconnected the ground wire and replace it with the new piece.

Help other customers find the most helpful instructions.

Were these instructions helpful?

151-160 of 160