http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/JMJR7WCM.gif
See part 3 in the diagram

Drive Belt

PartSelect Number PS3503117

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Pumps but will not spin.
  • Will not agitate.
  • Noisy.
  • Shakes and moves.
  • Burning smell.
  • Compare At

    $34.52
  • You Save

    $5.75
  • Your Price

    $28.77
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

67 of 81 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerFrancis from Rochester NY

Washer made loud banging noise during spin cycle

I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 27 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

Customerwendy from Naples FL

Belt came off

Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 28 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench(Adjustable)

Customerjohn from chester NH

Drum didn't turn/spin

1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 19 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerDoug from Hartselle AL

Would not spin of agitate

I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4