Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Peterlagerlof - February 23, 2022
Verified Purchase
Easy Repair - worked as expected
Just as expected - fast delivery - I am quite happy
★★★★★
★★★★★
Joe B - November 26, 2021
Verified Purchase
Somewhat easy to install
Somewhat easy to install The brand new pump that I received it’s very nice it’s running right now it’s quiet it seems to be a good quality part I took a good week to get here but it was worth the wait took me longer to take out the dishwasher and reinstall it that it was installing the new part thank you parts select your videos really helped out when I had to change the pump I’ll keep you in mind for the next project an appliance thank you again Joe B
★★★★★
★★★★★
Dennis P - November 25, 2020
Verified Purchase
Right part, easy install
This was exactly what I needed. While I had a pretty good idea what the issue was, the symptom descriptions were spot on. I showed my adult daughter this site and have not had to fix an appliance for her in years.
★★★★★
★★★★★
Rhonda K - September 16, 2020
Verified Purchase
Happy
came fast and in perfect condition.
★★★★★
★★★★★
Andrew T - January 15, 2020
Verified Purchase
So far so good...
The pump is working great. No problems with the order or delivery.
★★★★★
★★★★★
Chris S - May 21, 2019
Verified Purchase
Easy repair
Easiest fix on an a dishwasher. Now I don’t have to wash dishes by hand.
★★★★★
★★★★★
Lauri D - December 5, 2018
Verified Purchase
Easy repair
The part came in quickly and was just what I needed
★★★★★
★★★★★
Dave R - November 26, 2018
Verified Purchase
Worked perfectly
This part worked perfectly and was simple to install. Very happy with quality and service !!
★★★★★
★★★★★
Terry H - September 17, 2018
Verified Purchase
Pump motor kit
Shipping took a little longer than expected but after the pump motor arrived it only took about 20 minutes to get the old part out and replace with this one. Dishwasher is working just fine again
★★★★★
★★★★★
David B - May 2, 2018
Verified Purchase
Dishwasher pump replacement
Was the correct part as ordered, came with all parts, packaged well. Ordered on 24 April, received 2 May.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Faulty pump
Replacement was every bit as simple as the website said it would be.
Rick from SHICKSHINNY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump motor kit
Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part
Joe from FARMINGTON, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace dishwater pump.
Block and remove water hookup and drain hose. Ensure drain port on garbage disposer has a plug in it while drain hose is disconnected to ensure sink water does not find its way inside the cabinet. Place dishwasher with door facing floor. Remove electrical plug and pump retainer. Slide out pump. To replace pump reverse steps.
MARK from PORT ALLEN, LA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
pump failing
The pump was progressively getting noisier over time to the point we could hear it in the back of the house. The dishes were always clean though. Turned off breaker. Removed two screws attaching unit to cabinet. Pulled out unit as far as I could and disconnected power. Turned unit slightly so I could reach water connection and disconnecte
... Read mored it. Disconnected flexible drain hose, then could pull unit completely out of cabinet. Turned on it's side so I could access the motor. Removed two screws, steel retaining clip, then motor. Came with 2 new O rings which I lubricated and replaced. Reinstalled everything and problem solved, nice and quiet. One hour 15 minutes total.
Read less
matthew from DULUTH, GA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
7 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heard a sound like grinding when in washing cycle!
Turned power off , shut the water off to washer , unhook water line , unhook drain line from sink drain , unplugged electric chord from the wall . Open the door look where the door latches you'll see two metal strap' s that are screwed under the counter . Take the screws out . Take the bottom basket out .Take the spray bar off . There'
... Read mores two clips on the bar just push them out lift bar up .There in the middle of the washer you'll see filter screen. There's a small handle looking thing do not know what they call it .lol Twist one way or the other to take it off . Once you have that out of the way take the three screws out mine were hecksscrews .Pull the cover off remove the ball . Take a rag and take the excise water out in the bottom . Pull the washer completely out from under the counter . Lay it on the back side on the floor . You'll see the pump it has U shape metal holding it with two screws . Take the to screws out remove the U shape metal bracket . Unplug wire going to motor squeeze the clip and pull . Twist motor back and fourth and pull slightly till it comes out . Put new O rings on new motor and lubricate O rings and slide motor back in . Reverse the process . Take pictures if you need to as your taking things off if your afraid you won't remember.
Water pump went up, soap dispenser wouldn't close and a little rust on the lower rack.
Easy repair. pulled dishwasher out, disconnected electrical wire for safety but don't think it was required since the breaker was off (turn it on and flip the breaker for verification). Pulling the pump and replacing was easy, soap dispenser, same, easy. First time I ever worked on a dishwasher, simple. Parts were all OEM parts and most i
... Read moremportantly were the correct parts I needed. Way cheaper than replacing the unit and I saved $150 on an hours worth of work vice paying the service guy.
The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to dis
... Read moreconnect water and electric, 15 to reconnect.
Read less
Jeff from Lancaster, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
93 of 115 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak behind kick-plate
See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remo
... Read moreve 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.
Read less
Larry from EDWARDS, CO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
58 of 77 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
29 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
January 4, 2019
Dishwasher, fills, heats up but there is no pump or water flow action. Then it drains at end of “cycle”. No noise either after it fills. Is there a computer that could go bad? I’m thinking that’s not the problem as it seems to go through the cycles so the timer must be working. Otherwise I'm assuming it’s the motor. I can pull it and check it.
For model number LFID2426TF0A
Hello Bob, Thank you for the question. This might be an issue with the Circulation Pump, PartSelect Number PS3497737. This Pump and Motor kit is responsible for circulating the water through the dishwasher during the wash cycle. Hope this helps, good luck with this repair!
When i run the unit it puts out this extremely load humming sound ( almost like a grinding sound ) . Everything thing else works , it just a really load sounding ggggrrrrrrrr. Any idea ?
For model number FFBD2411NB
Hi Cullen, thank you for your question. It looks like most of the time the problem is with your motor. You could do a quick physical check of your wash arms to make sure there is no debris stuck that is causing that noise when the arms are spinning. I hope that helps. Good luck with your repair.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
January 24, 2019
Ran a load tonight and it just stopped, leaving two inches water below plastic filter circle. Soap partially emptied. When energized, the leds aren’t lighting up. Buttons are unresponsive. Tried turning breaker off 30 mins and on and hot/start combo. Nothing works/dead.
For model number FFBD2411NS6B
Hello Jim, Thank you for the question. This sounds like an issue with the Control Assembly, Part Number: PS8689162 for the Electronic Control Board, PartSelect Number PS11724123. With no lights on the controls, the most common part would be the PartSelect Number PS11724123. Thank you for your inquiry, good luck with this repair!
How can i test to find out if the pump is bad before i actually order the new motor/pump?
For model number FDB1050REC5
Hi Carrie,
Thank you for your inquiry. To verify if the pump is not working, you will need to use a multimeter to check the continuity of the part. If you are not familiar with how to use one, there are videos on YouTube that you may reference. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
May 23, 2019
Goes thru the cycle but water in the tub at the end
For model number FFBD2412SSOA
Hello Robert, thank you for inquiring. For this symptom you will want to replace either the Drain Pump part PS8689824, the Drain Hose part PS9494138 or the Flapper Valve part PS8689794. We hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Greg
November 18, 2019
My Frigidaire dishwasher is making a very high pitched squeal during the first 15 minutes of the wash cycle only. During the fill phase, last half of wash cycle and drain phase all operation sounds are normal. Would this motor part kit fix this problem?
For model number FFBD2411NW0A
Hello Greg and thanks for writing.
The circulation pump motor has bearings that wear out over time. When the motor bearings fail, they generate a squeal... Part of the pump and motor assembly (such as the motor bearings, drain impeller, or wash impeller) might be defective. changing the motor or the bearings should fix that problem. We hope this helps. Please contact us anytime.
3 people found this helpful.
Was this helpful?
Thank you for voting!
A
May 1, 2019
Frigidaire dishwasher: All buttons are glowing on the control panel except for delay start and start and the dishwasher won't start. Tried resetting with pushing heat dry and normal twice quickly and also with switching off and on but it won't start. Please assist what could be wrong.
For model number FFBD2411NS6B
Hello A, thank you for inquiring. For this symptom you will want to replace either the Pump Motor Kit part PS3497737, the Control Assembly part PS8689162, or the Door Strike part PS2331186. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
May 6, 2019
My dishwasher power wont turn on. I checked the breaker and ran a voltage tester on the wire / cord leading from the dishwasher into the panel and it has power. However the machine lights wont turn on in order to run a load. What could this issue be? Please help
For model number FFBD2408NB5B
Hi Mike,
Thank you for your question. If the dishwasher will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the pump motor, the door strike, the tub gasket, the spray arm and the latch assembly. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Casey
January 21, 2018
Motor doesn't run. How do i clean out filter?
For model number FDB520RHS2A
Hi Casey,
Thank you for your question. To clean the filter, you will first have to remove it from the dishwasher. Once removed, soak the filter in warm soapy water for 10 minutes and replace. Remove the baskets and pour one cup of vinegar on the bottom of the dishwasher followed by a cup of baking soda. Let it stand overnight and run an empty cycle the following morning. When the cycle is complete, scrub away any remaining dirt from the bottom of the dishwasher. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dan
September 24, 2019
What should the electrical resistance be across the leads of the motor?
For model number FFBD2406NB7B
Hi Dan,
Thank you for your question. To test the motor with a multimeter, disconnect the motor's two wire leads from the wiring harness. Set your multimeter to the R x 1 setting. Touch each of the meter's probes to one terminal each. Your motor should show little resistance (a reading of zero, or close to zero). Now check the ground connection. Place one probe on the bare metal housing of the motor. Place the other probe on each terminal, one at a time. You should not receive any reading on your meter from this test. If your dishwasher's motor fails either of these tests, you will have to replace it. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
