Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS3497647
This drive motor rotates the drum by turning the belt.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Unplugged Dryer; used screwdriver to push in and release two clips that hold top to front, tilted top back and removed two screws holding front to sides. Disconnected door switch and removed front .Reached in above motor to remove belt from around pulley and tensioner wheel, Pulled drum and belt out of machine.Removed approximately 10 screws around perimeter of blower housing and removed cover to access blower wheel. Removed outer lock ring from shaft and clamp from blower wheel hub, and removed blower wheel.Took out tensioner assembly.Disconnected wiring connector from motor.Removed three screws that held blower housing to bottom and removed retainer around rubber motor mount at pulley end of motor. Lifted out motor, blower housing and vent pipe as one unit. Removed 2nd outer lock ring from motor shaft.Rotated motor frame 45 degrees to free the rubber mount from the blower housing. Screwed new pulley onto new motor shaft and cleaned blower housing and vent pipe.Assembly is reverse of disassembly.Inspected and lightly greased the glides and inspected the idler wheels before reinstalling drum.Dryer works perfectly.Five to ten minutes also spent unscrewing and replacing timer knob and hinge pins on lid of matching washer Crosley cw22b5v.Very simple repair.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.
First lift the top and remove 2 screws holding the front panel on, at each top corner. Release the door switch from its clip (or disconnect the wires). Remove the front panel by tilting out and then lifting it up off the bottom tabs. Remove the belt from the motor by releasing the tensioner. Then lift the drum out. Remove the front blower cover, then remove the tensioner by first removing the spring, then pull the tensioner out toward the back. Remove the strap on the back of the motor near the pulley. It takes a little effort to get the strap off. Remove the 3 bolts holding the blower case (with the motor still attached. Remove the motor wires, then lift the motor and blower case out. Next remove the clip holding the blower fan on and remove the fan. It may be stubborn so be patient and slowly work it off. Remove the next clip behind the fan. Then remove the motor from the blower case by turning it counter clockwise (as viewed from the motor side). Installation is the reverse.
Unplug dryerPick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.
1. Opened top and removed wire clamps from side and front for door switch.2. Removed two screws and pulled front cover off.3. Removed drive belt from tensioner pulley and moved to back of dryer.4. Pulled drum off rear guide wheels and lifted drum out of dryer.5. Unplugged motor electrical connector and removed idler wheel spring and idler assembly.6. Removed screws holding blower wheel cover to case.7. Removed snap ring and spring clamp from blower wheel and pulled blower wheel off motor shaft.8. Popped rear motor clamp off with screwdriver.9. Unscrewed screw holding rear motor support to dryer bottom and removed rear motor support.10. Twisted motor assembly 1/8 turn to right and pulled motor rearward out of blower housing.11. Removed blower rear snap ring from old motor and moved to new motor shaft.12. Reversed procedures 1-10 to install motor, connector, idler, blower wheel, blower wheel cover, drum, belt, front cover and top cover.
Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.
I had to replace the whole motor, Idler spring and idler Pulley Wheel. It went well but I wish I could have replaced just the berring and not the whole motor.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.