Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS3497634
Note: This valve has been updated by the manufacturer and NO longer includes the removable pre-filter bracket connector. Must be ordered separately part number WPW10445062.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I followed the instructions from the web site video, and was very clear as to the details of my work. It was easy, and have ice cubes again.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I wasn't sure just where the actual valve was located so I watched the video available where the valve part was listed. I watched the video and did exactly as described and found the repair to be quite easy. I replaced the valve and my problem was solved. Thanks to PartSelect for adding this video with this part listing.
After watching the repair video on your web site, It too about 20 minutes start to finish to change the valve. It was great to have the video first while I was waiting for the part to be delivered, I would reccomend partselect to everyone . they were great to work with, everything was as it was souposed to be, Thanks Rob Berg
I have more than 10 years old Kitchenaid Superba black refrigrator that stop making ice. Initially I saw ice in the inlet tube, so I used hair drayer to melt it and it worked for a week. After that I did not see any more ice and not more water coming into the icemaker, so I ordered a new ice maker. That did not solve the problem. I worked with my old inlet valve and tried to repair it and I messed it up. I ordered this new inlet valve and and put it in and it worked and ice is good. So I have a new Icemaker and a new inlet valve
Took 5 mins. to install. I cut the hose with a razor one at a time then pressed into place. Then removed the wires one at a time so to not get them mixed up. I saved $125 .
Removed screws from back panel of fridge. Removed old valve. Removed water lines. Re-assembeled. Easy repair. Great directions. (The only thing confusing was the picture when ordering which didn't say that there was a part that needed to be removed for my particular model. My old part looked the same as the picture except yours had an extra part attached.) The directions received DID say to remove the extra connector, though.
undo nuts that mount the valve system to the fridge, oh, first unplug the fridge! Cut the plastic lines close to their existing nut or connection and then carefully make a very clean square cut on plastic line. Disconnect the electrical connectors, they are size coordinated to each of the two solenoids and match up to the new ones. Re-connect the electrical connectors, plastic lines (these too are size coordinated) re-mount the valve kit and plug in. Can't get any easier.
1) Removed the two screw holding the valve2) cut exisiting hoses off old valve3) put hoses on the new valve4) reattach valve to refridgerator
Removed bottom panel on fridge , removed the two screws holding valve, removed electrical connections and water connections and replaced the wires and tubes and attached the valve to the fridge, replaced lthe panel and the was it in less than fifteen minutes.
Use a 1/4 inch nut driver, took out the old one and put in the new one. After I completed the repair it took a minute for the ice tray to fill up. The video you provided was right on. It made the job very simple.
Removed the old water inlet valve assembly. Verified that the line to the icemaker was not blocked. Installed the new water inlet valve assembly with no issues, and the icemaker started working right away.
Turned water to ice make off. Removed 2 screws holding inlet valve. Removed 1 water line going in and 2 water lines going out to water dispenser and to ice maker. Reattached water lines back into quick disconnects. Fasented inlet valve back on the frame with the 2 screws and turned water back on. Easy and quick. Thanks to Parts Select for super fast delivery of parts, 24 hours turnaround. Thanks Jimmy.
I followed the directions in the video. The repair was not difficult. The water flow came back to the front door dispenser, but I couldn't get water to the ice maker.
Pulled the old valve off and went to put in the new one. They two valves are slightly different but in the end, it worked and everything is fine.
I first discovered the problem when there was water on my floor.I found out that the icemaker had quit making ice, but I still had water in the door. I filled the icemaker manually with water to see if it would make ice, which it would not. I ordered and I installed the icemaker, which was only 3 screws with the nutdriver and remove the power harness which took about 15 minutes (very easy), but it would still not make ice. I then ordered the water inlet valve kit. When I received this part, the first thing I did was watch the video on how to replace it. I cannot stress enough that you should watch the video first!!! After that it took 10 minutes to replace the new valve and I had ice again.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.