3486910-1-S-GE-WD12X10327-Upper Roller and Axle - Kit of 4
3486910-1-S-GE-WD12X10327-Upper Roller and Axle - Kit of 4 3486910-2-S-GE-WD12X10327-Upper Roller and Axle - Kit of 4 3486910-3-S-GE-WD12X10327-Upper Roller and Axle - Kit of 4 http://www.partselect.com/Schematics/GE/GE_Thumb/00124321i02.gif

Upper Roller and Axle - Kit of 4

PartSelect Number PS3486910

This is a kit if 4.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door won’t close.
  • Not cleaning dishes properly.
  • Noisy.
  • Door latch failure.
  • Compare At

    $12.38
  • You Save

    $2.06
  • Your Price

    $10.32
In Stock
Order within the next 10 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 133 reviews What's this?
26-30 of 133
 

1 of 1 people found this instruction helpful

Parts Used

  • Upper Roller and Axle - Kit of 4

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerKenneth from Jamison, PA

Broken top roller rack

Took off the end cap- hardest part- took some twisting-be careful not to break it. After that slid out the old part and just popped the new one in. Then it took a little while again to put the end cap back in. No tools needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Roller and Axle - Kit of 4

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerAlexander from Commerce Township, MI

Top rack roller was binding.

I pried out the slide stops (just twisted the little plastic tab on the stop). Slid the top rack out. Popped four roller assemblies off. Popped four new ones back on. Aligned the top rack with the slides and slid it back in place. Finally, rocked the stops back in place by inserting the bottom first and pivoting the top. Had to use pliers to move the little plastic tab stops into the upper channel. Done. Works like a champ.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Roller and Axle - Kit of 4

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerBarry from Mohrsville, PA

Plastic parts worn and cracked

First I removed end caps of top roller rack. Caps have small squeeze tounge that must be squeezed and twisted to remove. Then simply roll out rack. plastic clips and wheels are easily removed and replaced.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Roller and Axle - Kit of 4

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerBruce from Mahwah, NJ

Upper rack was coming apart

The trick in replacing the roller wheels is to remove the plastic/rubber "stop" that is attached to the front of the stainles steel track. I used a pair of needle nose pliers to bend the small plastic extension on the "stop" so it would be released and then remove the "stop" from both tracks. Once that is done then simply slide out the rack assuming some of the wheels are still attached to the tracks and/or the wheels.

The next step is to install the new wheels onto the rack. Then, slide the rack/wheels onto the tracks. Then, snap the "stops" back onto the racks.

You're done!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Roller and Axle - Kit of 4

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrederick J from Howell, NJ

The rollers cracked and broke off the rack

Used a small flat head screw driver to remove the rail end covers (2) and removed the rack. Used my thumb to push the snap on roller assembly off the rack. The new rollers snap right back on the rack with just fing pressure. Re-installed the rack and then just pushed the rail end covers back on.

Very Simple Repair to a great machine. First problem in 13 years and still works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

26-30 of 133