348557-1-M-Whirlpool-358684-Lid-Strike.jpg
348557-1-S-Whirlpool-358684-Lid-Strike.jpg 348557-2-S-Whirlpool-358684-Lid-Strike.jpg 348557-3-S-Whirlpool-358684-Lid-Strike.jpg

Lid Strike

PartSelect Number PS348557

This part is used to activate the lid switch when the lid opens/closes.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Will not start.
  • Timer will not advance.
  • Will not agitate.
  • Compare At

    $4.21
  • You Save

    $.70
  • Your Price

    $3.51
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 4 reviews What's this?
1-4 of 4
 

68 of 84 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerFred from Midlothian VA

Washing machine kept cutting off mid-cycle

I had to remove the washing machine from the laundry room (our laundry room is pretty small).

I read the do-it-yourself explanation posted by Paul From Glendale CA and followed his instructions.

1. Unplugged the Washer and disconnected the hoses, so I could slide the washer into the kitchen.

2- Unfastened the two screws in the front lower corners of the controls panel and tilted is back. Unfastened the old lid-switch wiring from the control panel.

3. Remove the clips at the two corners under the control panel. I rotated the cover forward to clear it from the back and lifted it off and set it off to the side.

4. While I had the Washer disassembled I vacuumed out all the accumulation of dust, etc.

5. Removed the lid switch and unfastened the ground wire.

6. Installed the new switch and reassembled the Washer.

7. I did not read Paul's reassembly instructions closely enough. The front flange of the cover goes UNDER the steel frame on the washer. I spent 30 minutes trying to get the cover on, then finally figured that out on my own. Once I got the flange under the frame, it took about five minutes to get the cover on, the clips in and the control panel back into positions and reassembled.

The entire process is not particularly difficult. Had I read the "UNDER the frame" part earlier, the entire repair would have taken no more than 45 minutes.

Having another person to help reinstall the cover would be helpful. The cover is not heavy but it is a little awkward to handle and having another person to help line up the back cover, etc. will make the reassembly even easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 16 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerMatt from Sussex WI

Washer did not spin.

First I removed the two screws on the back side of the switch panel and tilted it back to expose the controls. I then pryed up the top of the washer to expose the lid switch. This was a mistake because I damaged the clips and bent the metal frame. Anyway after that I unlatched the lid switch on the top side, pulled it through the bottom, removed two screws holding the lid switch in place and replaced the switch and lid switch strike. Because I wrecked the machine top I had no alternative but to drill two holes from the top and put two screws in to hold the top down. It's ugly but it works.
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 18 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerLARRY from LUCERNE CA

Shut off before finished

i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 48 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerKenneth from El Paso TX

Machine would stop when finished rinse cycle and wouldn't spin or drain.

I replaced the Lid Switch and the unit works fine. I also cleaned up some other issues in the unit which took about half the time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4