348406-1-S-Whirlpool-357574            -O-Ring
348406-1-S-Whirlpool-357574            -O-Ring http://www.partselect.com/Schematics/Maytag/WEZNWE9Z.gif

O-Ring

PartSelect Number PS348406

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Leaking.
  • Compare At

    $7.79
  • You Save

    $1.30
  • Your Price

    $6.49
Special Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 11 reviews What's this?
1-5 of 11
 

14 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Gerry from Tenino, WA

Washing machine not spin drying

Please note that there is a very though instruction video under, PS 334641 clutch assembly, which deals with this subject. I removed the three bolts holding the motor and transmission onto the center post and the screw holding the agitator to the center drive shaft. I also removed the wiring harness to the motor. I then pulled the motor and transmission out the bottom of the machine. I found that that there was a white nylon drive part, which was broken, that connected the transmission to the center agitator shaft, through the brake mechanism. That's why the machine didn't spin dry. The brake mechanism was full of transmission oil, which might have caused or contributed to the problem. When I looked for the PS334641 clutch assembly, which contained the part I needed, I found the video that showed me how to remove the part properly. The part wasn't that hard to change, but I also decided to change the gear case cover seal PS340984, because of the oil leak. That's a bit tricky if you haven't changed a seal before, but an automotive shop could probably change it for you if your transmission was leaking. I wasn't able to remove the out side covering of the machine, but there was enough room to work from the bottom. Following the video, the rest went well, but I should have changed the rubber motor drive part that connects the motor and the transmission, since it was pretty worn. Next time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Thomas from Troy, MI

Upper agitator & cogs wore out

I pulled the cap and took a socket wrench turned the stud agit off and removed the upper agitator. Than I assembled the new agitator with the new clogs put the agaiator back on and tightened the stud agit. Replaced new cap and done! Easy job!! Everything is working like new again. This whirlpool washer is 14 years old and still going strong!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Wrench set
Customer: Bruce from Matthews, NC

Washer shakes violently in spin cycle

It took a lot of surfing the internet to find good web sites for information. One was part select . I removed the cabinet from the washing machine per instructions. Then I replaced the suspension springs. That was easy. Took about 10 minutes. However, it didn't fix the problem. So I decided to replace all the suspension pads without a total tearing down the unit. It was almost impossible to put the new ones in because they don't press in easily. One other thing, there are plastic cups with pins in them that look like they are missing cotter pins. After hours of searching. I found partselect.com
THESE ARE THE SHIPPING PINS THAT KEPT THE MACHINE FROM MOVING AROUND DURING SHIPPING. THEY TOOK THE COTTER PINS OUT AFTER SHIPPING. THEY ARE NO LONGER NEEDED. My story ends here because my machine is still shakes violently. I have offered my washing machine for parts on our local freecycle website so as to keep it out of the landfill.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers
Customer: John from Yakima, WA

Dishwasher was leaking

Removed the old parts, Cleaned the area around the gasket and put in the new. Worked great the first time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Socket set
Customer: WILLIAM from CORAOPOLIS, PA

Agitator would not turn

Removed the stud bolt in the ag[tator and removed the agitator from the machine. J then seperated the agitator in two pieces and installed the new dogs.I then installed the agitator back in the washing machine and it performed beautifully

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11