347627-1-M-Whirlpool-349241T-Drum-Support-Rollers.jpg
347627-1-S-Whirlpool-349241T-Drum-Support-Rollers.jpg

Drum Support Rollers

PartSelect Number PS347627

These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Will not start.
  • Compare At

    $24.10
  • You Save

    $4.02
  • Your Price

    $20.08
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Maintenance Kit

Part Number 373087

This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, four tri-rings, and one clip. This part can be used with both gas and electric dryers.

$42.52
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 83 reviews What's this?
 

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerSteve from Hurst TX

My dryer sounded like a thrashing machine when it was running

Removed the top and front panels and then removed the drum. Discovered that one of the drum support rollers was worn out. The center bushing of the roller was worn away causing the roller to wobble as the drum turned. I replace both support rollers and the belt. Now the dryer sounds like a sewing machine when running

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set, Wrench(Adjustable)

CustomerMilton from Norfolk VA

Drum not rotating

Replaced drum support rollers but did not fix problem. Motor was fried! Replaced with used motor. NOTE. Make certain you install motor in the right position or you will find the drum sitting on motor. The guide must be in the 4 o.clock position and then placed in bottom groove for proper alignment of motor to drum. Job was amazingly easy and online instructions were super helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Wrench set

CustomerEric from Fort Dodge IA

Dryer drum not turning and no air circulating

replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers
  • SEAL

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerNesco from Beltsville MD

The drum roller wheels needed to be replaced. The drum seal was damaged.

Followed the instructions from the video on hour website. It was quick and easy. The only thing that took time was waiting for the glue to dry.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerMichael from West Seneca NY

Noisy dryer

My 20 year old dryer sounded more like a washer on spin cycle. A quick web search showed it was probably the roller wheels. I disassembled the dryer and found the roller bearings were gone. I ordered parts including the rollers and the rear felt seal and got the package in 3 days. Unfortunately, the wrong seal was in a mismarked package. PartSelect associate randy helped me out and I got the right part in 2 days. After that, the repair only took an hour. My wife went into the basement where I was catching up on the wash, and she didn't even notice the dryer was running!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerBrian from Spencer MA

Machine would not agitate properly and noisy dryer

took off fabric softener dispenser. used socket to remove agitator. Cleaned and then replaced the little plastic dog ears...works like brand new! It took 15 minutes or less.

Also repaired noisy dryer. replaced drum rollers, pulley and belt. The job took about an hour and was real simple. However..the dryer was still noisy. Fixed with a prybar to force drum to be tighter. It now sounds like brand new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerWes from Duluth MN

Drum stopped turning

I pretty much followed the instruction sheet that was included with the new drum belt BUT, this should be added in step #2. "If working alone" Before removing the front door panel: A)pull down lower access panel. B)Support the weight of the drum. (This can prevent damaging the rear drum seal!).
Also, instruction sheet step #5 should read: Route belt through the idler pulley bracket (by pulling side of bracket open enough to insert belt) and then around the motor pulley.
Step #7) A putty knife with the end rounded off works best!
Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerBrad from Lake City FL

Buzzing sound while start button pushed. Then shut off after 30 seconds.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerGerald from Germantown MD

"banging" or "bumping" noise when using drier - caused by broken support roller.

Remove screws from dryer vent. lift top up: use screw driver to pry up and release top panel its uses a simple catch. Remove wires from door switch. Lift up and remove front panel from clips on side of drier body. IMPORTANT: two people required - Drum will fall if not supported when front panel is removed. Get down in front of machine: one peron holds drum in place an you push up on belt tensioner. Release belt from drive wheel. Remove drum and set aside. Pry off support clip from front of broken support roller. Clean roller shaft (replace if broken). Place new roller on shaft. Replace support clip. Have second person hold drum in place while you re install drive belt (see above). Replace front panel. Re attach wires to door switch. push top panel down (firmly to lock). replace drier screws.
good luck

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • RING
  • Drum Support Rollers

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerMichael from Marion KY

Noise in dryer when dryer was turned on

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerSTEVE A from BAYTOWN TX

Drum support rollers seized and not turning.

Removed the two screws to the lint screen. Popped open the top panel and swung up to open.
Removed the two socket head screws holding on the front panel and then lifted up and out to remove the panel.
Disconnected the drum belt from the bottom tensioner pulley and then removed the drum.
I then replaced the two drum support rollers and the belt tensioner pulley. I put the new belt around the drum and reinstalled the drum. From the bottom, I threaded the new belt around the new tensioner pulley.
I then reinstalled the front panel and top panel in the reverse of disassembly.
All went well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

Customerbenny from yuba city CA

Rumbling noise inside dryer

first removed 2 screws under lint screen door ,then popped up top of dryer (lid),removed 2 screws holding front cover of dryer on,removed front cover,after removing 2 wires from door switch,then took belt off of drum by releasing tensioner,removed drum to access drum rollers,removed old rollers & installed new rollers,and reassembled by reversing this procedure

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerEthan from Manchester CT

Loud noises when dryer was spinning.

I started trying to locate the noise. I started to remove screws in the rear plate. Removed the rear plate. Couldn't find the noise. Had to remove the top cover and operational controls. Couldn't locate the noise. I figured it was a bearing that went bad somewhere, but I coulnt find it. During the search for these drum rollers I was able to thouroughly clean out old debris and lint caught in the machine for years. Finally I located the bottom front cover, took it off, and located the problem.

At this point I went online, located the part with these guys, ordered it and got it delivered in like 2 days. Pretty quick.

I then went back and replaced the both drum rollers in like 1 hour.

Dryer works and sounds great now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Support Rollers

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerHarold from Coyle OK

Made a lot of noise

Took of the old roller and replaced it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJudah from Lompoc CA

Dryer was making a really loud noise

Opened up the front of the dryer. Saw that the belt was partially torn. Also noticed that the wheels weren't very smooth. So went online, found this website, measured the belt described with the one in the dryer after I took it out. Also replaced the drum rollers because they were worn down. Received the parts in 3 days. Immediately replaced the parts and sounds like new. No noise and works great! I'm happy and so is the family. Thank You! Why pay more for replacement parts at Sears.com or otherside when you can get them cheap here!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?