Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS347627
These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings and one palnut.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
NOTE: This kit is for 29" wide dryers built 1965 or later. Please verify model # before ordering as may not work for all models.
This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, four tri-rings, and one clip. This part can be used with both gas and electric dryers.
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and replaced the rollers and tri rings and reassymbled the dryer.It was a very simple repair.Thanks Mike
Help other customers find the most helpful instructions.
Were these instructions helpful?
Dryer started making noises years ago. Finally it was intermittently starting, then...didn't start at all. It made a buzzing noise, like the motor was in over-torque. Then it over heated and wouldn't do anything until it cooled down. Then the cycle started all over again. I thought it best to change out all the worn parts. Found the belt, the rear seal, the rollers and motor all needed to be replaced. All were very simple to do. Followed the instructions and videos from others located on this site.
Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I disassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.The first thing was to remove the front coverand the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out. At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
took off fabric softener dispenser. used socket to remove agitator. Cleaned and then replaced the little plastic dog ears...works like brand new! It took 15 minutes or less.Also repaired noisy dryer. replaced drum rollers, pulley and belt. The job took about an hour and was real simple. However..the dryer was still noisy. Fixed with a prybar to force drum to be tighter. It now sounds like brand new.
After reading about repairs to the drum rollers, it was suggested to change the rear drum seal at the same time. The drum rollers were very easy to change and took no time at all. The rear seal was a different story. The instructions in the packet could have been more explicit. The seal has to be streched around the drum at first. Then and only then can you install the seal on the drum edge. You should also have several clamps available to hold the seal in place as you glue the outside flap. Leave the clamps in place until the glue dries, then re-install the drum.
lifted top section of dryerremoved front dryer panelremoved drum belt and tensionerremoved both drum rollerscleaned both roller axlesinstalled new rollersreassembled remainder of dryerif you are at all mechanically inclined, it is a simple job
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Removed lint filter and 2 screws on either side of lint filter housing. Pried front part of top panel up on both sides and flipped backwards out of the way. Disconnected wire to door-open switch. Supported top panel with a standup dolly/handtruck so that it didn't put stress on the back mounting clips at the back of the top panel. Removed 2 screws securing the top of the front panel to the two side panels. Lifted the front panel up to release it from the clips at the bottom of the two side panels. Set front panel aside. Laid (layed?) dryer on it's back. Lifted out drum, removed old belt. Removed screw holding base of strut to bottom of dryer frame (left support roller when facing front of dryer). Pried off push-on washer/clip securing strut to roller shaft. Pried off triangle washers holding rollers on shafts. Vacuumed loads of lint out of the inside of the dryer. Reassembled in reverse order. A little tricky getting the belt back on the drum, through the pulley/tension wheel and around the motor spindle/spool thingey. With the machine still laying on it's back I wound up using masking tape to hold the belt onto the middle of the drum while threaded the rest of it into place to the motor. Problem was due one of the support rollers having a flat side instead of being round.
removed the top of the dryer exposing the drum and belt.Also the bottom acess door was removed.The rollers were easy to get to from the bottom and from the back.Had to remove ducting from the rear of the dryer to expose the upper most roller shaft nut.Loosened the nuts from the back making the wheels come from the bottom.Also had to loosen the support bracket holding the weight up on the bottom roller assy.Replaced the belt by rapping it around the drum before installing the roller wheels.This project was easy except trying to hold the upper shaft in place while putting the nut back on the shaft.This would be much easier with a second person.Thanks for making this a nice experience and easy fix !
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.