346995-1-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4"
346995-1-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4" 346995-2-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4" 346995-3-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4" http://www.partselect.com/Schematics/Maytag/UTGT4VNQ.gif

Multi Rib Belt - 92-1/4"

PartSelect Number PS346995

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.
  • Will Not Start.
  • No heat or not enough heat.
  • Takes too long to dry.
  • Heat stays on after drum has stopped.
  • Touchpad does not respond.
  • Compare At

    $11.53
  • You Save

    $1.92
  • Your Price

    $9.61
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Idler Pulley Assembly

Part Number 383724

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

$9.66
In Stock

Maintenance Kit

Part Number 373087

NOTE: This kit is for 29" wide dryers built 1965 or later. Please verify model # before ordering as may not work for all models. This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, four tri-rings, and one clip. This part can be used with both gas and electric dryers.

$30.84
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 313 reviews What's this?
 

25 of 41 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set, Wrench set
Customer: DAVID from LEESBURG, FL

One of the power cord connections on the terminal block was loose. Screw on terminal block was cross threaded when installed. Took six years to smoke the wire.

Removed and replaced terminal block, power cord and black wire to timer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 23 people found this instruction helpful

Parts Used:
  • Multi Rib Belt - 92-1/4"
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Douglas from COMMERCE, TX

Replaced belt while I was in there replacing motor

If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

32 of 63 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Mike from Mantua, NJ

Replace the ribbon cable for the water/ice dispenser

I replaced the paddle for the water dispenser in the refrigerator and in that process the ribbon cable shorted out from the bending and the electricity did not go through so I ordered a new
ribbon cable which was easy to install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Ray from Raphine, VA

Dryer not getting clothes dry in one cycle

Raise the top of the dryer. This exposed the elements in the back. Removed old elements,paying attention to where the wires go.
Installed new elements, hooked the wires up, and I was done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 14 people found this instruction helpful

Parts Used:
  • Multi Rib Belt - 92-1/4"
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Scott from Bayport, NY

Change dryer belt

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?