345113-1-S-Whirlpool-3392519           -Thermal Fuse
345113-1-S-Whirlpool-3392519           -Thermal Fuse 345113-2-S-Whirlpool-3392519           -Thermal Fuse 345113-3-S-Whirlpool-3392519           -Thermal Fuse

Thermal Fuse

PartSelect Number PS345113

Manufacturer Part Number 3392519
Manufactured by Whirlpool

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.
  • Takes too long to dry.
  • Shuts off too soon.
  • Will not tumble.
  • Timer will not advance.
  • Will not shut off.
  • Too hot.
  • Touchpad does not respond.
  • Compare At

    $13.33
  • You Save

    $2.22
  • Your Price

    $11.11
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 270 reviews What's this?
76-90 of 270
 

1 of 1 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerThomas from Oceanside CA

Dryer would run but not heat up

The repair, replacing the thernal fuse was easy, just one screw and then remove and replace by disconnecting and reconnecting two wires. It did take a bit of time to find which part was defective. I first removed the back panel and front panel and the drum to get at the igniter and flame window. I checked continuity of these parts as well as the gas solenoids and they all checked out ok. The thermal fuse was last on my list. It read as an open circuit. I temporarily jumpered the two wires at the fuse and checked that the igniter would now heat up. I spent over one hour removing the ductwork and giving the unit a thorough cleaning with a shop vac.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJoseph from Mountain Top PA

Dryer would not run

First I checked for power at the outlet (240volts-power good). I then removed 9 screws holding the back cover. I then turned the timer to run position and pushed the start button this allowed me to hear the timer andvance. So I disconnected power to the dryer and removed the wires to the thermal fuse. I then took a ohms reading across the fuse...it showed open. Removed one screw replaced fuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRudy from Forest Hills NY

Dryer stopped

Dryer stopped in the middle of a cycle. I opened the back and traced the feed wires from the power cord. With a volt meter I checked the thermal fuse which is were the power cord goes to first. It had power on the line side and none on the load side. this is the easy fix. Ps unplug unit while tracing the wires. Most of this is done without seeing them very clearly. I should also say I am a licensed Master electrician with over 30 years of trouble shooting.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJeff from Moberly MO

Dryer just quit

Took back panel off dryer, unscrewed old part, put on new one. Easy fix. Dryer works great again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 7 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customermary from Maple Plain MN

Dryer was totally dead, had power to the outlet.

I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 7 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRussell from San Jose CA

Dryer stopped working

How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Thermal Fuse

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerFrank from Sicklerville NJ

Thermal fuse was blown

First I tested the fuse using my Volt-ohm meter, which showed a zero reading. So I knew what I needed and ordered it from you guys. To be safe I took the dryer apart and cleaned it good, when and while I reassembled it I replaced the old fuse with the new and now she's like brand new> I spent about $12.00 but I saved $600.00..Thank You "PartSelect"..

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerVito from Levittown NY

Dryer wouldnt turn on.

Followed the instructions in the video provided on the partselect website. The video's instructions were excellent. Simple removed the back comver of the dryer, located the parts and replaced them. It would have cost me at least $500 for a new dryer. At least $150 to have a repair man come. I did this repair myself for $45!! I highly recommend partselect.com.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerMark from Mountain View CA

Takes too long to dry

I was directed to the cycling thermostat for my problem. The thermal fuse was another possibility. I was too lazy to check them with a VOM before ordering so I ordered both. The repair video was helpful and the assembly diagram was useful for locating the parts. I removed the 9 back panel screws with a 1/4" socket wrench and removed the panel. Each part is held with a sheet metal screw which are removed with a screw driver. The connectors were very tight and I used pliers to pull them off the parts. The parts pop out of the mounting slots and are easily replaced and secured with the screws. I labelled all the wires (2 for the thermal fuse and 4 for the thermistor) but the polarity probably does not matter. I replaced the wires, replaced the back panel and replaced the 1/4" screws. The dryer works again. I checked the old parts with a VOM and found that only the cycling thermistor was bad, so now I have a spare thermal fuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver

CustomerWilliam from Coalinga CA

Dryer would not start

I had worked as a stationary engineer/refrigeration mechanic for large commercial building/plant systems for several years at journey level. I also had worked as an instructor in this field. However I have not done much of this type work for several years. Using the wiring diagram contained within the control panel at the top of the dryer, was able to trace the sequence of operation to the component i suspected (thermal fuse). It was the thermal fuse per check with ohm meter. Instructions on the dryer internals indicated if thermal fuse blown to also replace cycling t stat. I also found that the blower unit was full of microdirt/lint, which was restricing airflow-vacuumed. ordered the parts overnight, and replaced. works fine now.The unit is my household electric dryer, made by whirlpool but sold under the kirkland costco brand. When i worked as a journey level technician, i always noticed that whirlpool product are generally a better quality than most, and have better parts availability, and ease of repair. this still holds true.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerCharles F from Belle Mead NJ

Drier without heat

all sensors/fuses were measuring open at room temperature with an ohmmeter.
Called Whirlpool for drawing and install and got nothing.
Found nice video on you tube.
Unscrewed and replaced each device one by one.
The terminal mod went exactly as portrayed.
Owner pleased.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 20 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

Customerstacy m from akron OH

No heat

First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerThomas from Walnut CA

Timer will not advance - heat on about 10 minute then off - take a long time to dry load

Replaced thermal fuse, cyling thermal, then replaced thermostat 205F, ptoblems still remained.
Using ohmmeter measured and inspected all components . Found that the valve coils a little bit stick to the shaft. Orderd the two terminal gas valve coil and secondary coil valve - three terminal and replaced. Problem solved. :-)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerJames from Palmdale CA

Thumping noise when dryer on

FOUND THE DRUM ROLLER WORN OUT. REPLACED THE ROLLER, BELT AND IDLER PULLEY. TOOK DRUM OUT AND REPLACED PER YOUR INSRTUCTIONS.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerLawrence from Houston TX

Dryer was working but no hot air

Actually two sets of parts were purchased. First I replaced the Igniter, thermostat and cysling thermostat. I would suggest starting out replaceing the thermal fuse and then go down the list. The last part I replaced seemed to be the problem. Replacement of the thermal fuse and thermostats was very simple, remove the back and replace the parts. The coil and igniter were more difficult. I had to remove the screws form the lid, pry open the top, remove inside screws and then access the igniter and coil. Instructions provided for igniter were useful, but there was one screw hidden from view that was not included in the instructions. Dryer is now working

Help other customers find the most helpful instructions.

Were these instructions helpful?

76-90 of 270