| |
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsSocket set
CustomerCharles from Long Beach CA
No heat...
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Socket set
CustomerDouglas from Fernley NV
Dryer got hot then heat would shut off
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
|
4 of 12 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Socket set
CustomerJoseph from Baldwin NY
No heat would not shut down
as i took a part out I put back wire for wire part for part took my time no distractions great to have this service would use again and tell a friend or friends great stuff saved $$$$$$$ thank you for being their love this internet
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers
CustomerGarrett from Vineland NJ
Dryer did not get hot
Found on your site the top two causes of a Dryer not getting hot enough and ordered those parts ( which were delivered quickly).Removed the top two screws that hold the front of the dryer that gives access to the coils and flame sensor assembly after lifting up the top.It took more time to clean up all the lint than to replace the parts.Dryer works great!
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerRobert from Newmarket NH
Dryer started with heat and than went cold.
First tried to clean the ignitor, broke it and replaced with new. Problem not yet solved. I read a review where one guy replaced all components as they were reasonably priced so I did the same. Replaced coils and flame sensor (which I was going after next anyway). Dryer is now back in service and the house is back to normal.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers, Socket set
CustomerMichael from Lancaster NY
My dryer did not heat up
Prelude to this was 2 years ago we had the same problem, called Sears and $200 later we had a new $16 dollar part, the repair guy was kind enough to tell me what he did, and I saved the fuse he replaced. So when it happened again this summer, I went through a couple of sites (obviously including this one) to find parts, started with the fuse he had replaced, which was not the problem this time, went on to the next likely, and on through about 5 key elements (all under $20) until I found the coils on the burner assembly were the problem. All in all the repairs were pretty simple, and once I figured out how to dismantle the cabinet safely. I am VERY happy with the timely replacement parts (shipped very quickly) and when your dryer isn't working-things pile up pretty quickly. The dryer is working like a charm again. Thanks! -Mike
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers, Screw drivers
Customerbrian from butte MT
Would ignite but not run for more than 10 min.
Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerLorraine from Arroyo Grande CA
Flame did not cycle on and off as it should. It only came on once so clothes did not dry.
After the Radiant Flame Sensor was installed, the problem remained. An appliance repair person then replaced both coils, and that fixed the problem.
|