344510-1-S-Whirlpool-3387134           -Cycling Thermostat
344510-1-S-Whirlpool-3387134           -Cycling Thermostat 344510-2-S-Whirlpool-3387134           -Cycling Thermostat http://www.partselect.com/Schematics/Maytag/RSDYZ2AA.gif

Cycling Thermostat

PartSelect Number PS344510

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Takes too long to dry.
  • Will Not Start.
  • Timer will not advance.
  • Too hot.
  • Shuts off too soon.
  • Will not shut off.
  • Will not tumble.
  • Compare At

    $16.56
  • You Save

    $2.76
  • Your Price

    $13.80
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Thermal Fuse

Part Number 345113

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".

$9.39
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 117 reviews What's this?
36-40 of 117
 

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Joseph from Mountain Top, PA

Dryer would not run

First I checked for power at the outlet (240volts-power good). I then removed 9 screws holding the back cover. I then turned the timer to run position and pushed the start button this allowed me to hear the timer andvance. So I disconnected power to the dryer and removed the wires to the thermal fuse. I then took a ohms reading across the fuse...it showed open. Removed one screw replaced fuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Cycling Thermostat
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: sheldon from macon, GA

Dryer want heat up

they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Chris from Taunton, MA

Clothes coming out damp, after a 60 min cycle

1. Unplug unit, next disconnect vent then remove back cover. 2. replaced element (very easy) then 2 thermostats, then put cover back on. 3. Removed frt. cover by following directions that came with maint. kit this too was easy. The hardest part is getting belt on as your putting drum back in, and even that was only so hard. Just TAKE YOUR TIME, and you will get it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Gerard from Huntington, WV

No heat in dryer and lint filter torn

Dryer didn't heat. I got the heating element thru sears and when I ordered it I thought I should also order the thermostats but I didn't. Element arrived two days after ordered right on time. Slipped right in in a few minutes. Turned dryer on. No heat. Went back to drawing board. Watched videos on part select site and realized I needed thermostats. Ordered them and lint filter. Arrived right on schedule and also slipped in in no time flat. Turned dryer on and yes it heated perfectly. Wife was pretty impressed with new lint filter as other one was torn with jagged edges. MY SUGGESTION: if your dryer doesn't heat and you can't test each individual item thermostats and heating element order the three of them ( high limit and cycling thermostats and heating element) cause they'll probably will all go at the same time anyway. Then won't have to wait on the second shipment if things don't work with partial replacement. Parts select was great and videos are well understood and easy to follow. Would certainly use again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Mark from Mountain View, CA

Takes too long to dry

I was directed to the cycling thermostat for my problem. The thermal fuse was another possibility. I was too lazy to check them with a VOM before ordering so I ordered both. The repair video was helpful and the assembly diagram was useful for locating the parts. I removed the 9 back panel screws with a 1/4" socket wrench and removed the panel. Each part is held with a sheet metal screw which are removed with a screw driver. The connectors were very tight and I used pliers to pull them off the parts. The parts pop out of the mounting slots and are easily replaced and secured with the screws. I labelled all the wires (2 for the thermal fuse and 4 for the thermistor) but the polarity probably does not matter. I replaced the wires, replaced the back panel and replaced the 1/4" screws. The dryer works again. I checked the old parts with a VOM and found that only the cycling thermistor was bad, so now I have a spare thermal fuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

36-40 of 117