| |
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerWendy from Wickenburg AZ
The 'nozzle' end of the arm tube fell into the bottom of the dishwasher, and was partially melted by the heating element.
One screw was taken out, the old arm removed, the new one put in place, then attached to the new arm tube holder. TADA!!!! Done.
I am a widow, and think I saved about $75.00 doing this job myself. Thank you.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLaura from Marietta GA
The original, detachable hose portion developed a hole and needed replacement
Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCharles from Hopkins MN
Broken mount caused dishwasher to shoot water against door, caused leaking
Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.
|
2 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
Customersaul from clarks summit PA
Dishracks old and worn
Did not have to do any repair, the parts for the dishwasher come with all the necessary parts and no tools were necessary. the wheels were snapped into place for the lower rack and the upper rack should needed to be place in the sliders. The Middle arm holder is not necessary as it comes standard.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMicaela from Essex MD
Mount for the upper spray arm was broken
After getting the model number of our dishwasher we checked for the parts on Part Select and found the diagrams very helpful in identifying the exact part we needed. When it arrived only days later we were able to attach it to the upper rack by the diagrams on Part Select in minutes. We tightened the screw and that was it! So happy to have my dishwasher working again like new!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerHugh from Millington TN
The upper spray arm was broken off
Looked up the model number, went on Google to find vendor. Found part in a drawing on vendor's website. Ordered the part for 2nd day delivery. Replaced the part in 10 minutes and started the dishwasher. No problems.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerStanley from Liverpool NY
Washer are retainer nut broken
The washer arm retainer nut was broken and the washer arm was dislodged Decided to replace the sprayarm and wash arm bearing ring as they looked worn. Middle wash arm tube holder had been broken but was wired together. Decide to replace it as well. Fedex deliver the package and I was running the dish washer fifteen minutes later. Great service and a simple repair
|
0 of 1 people found this instruction helpful
Parts Used
-
- Middle Wash Arm Tube Holder
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerColleen from Coram NY
Melted tube holder(melted after fell on coils below
After opening the bag the part came in I noticed the ring was sliced with an opening in it, unlike the old part.After calling the help line and explaining my delelma The person on the line read the instructions to me which detailed the part which explained that the part was supposed to have a cut in it.
|