343923-1-S-Whirlpool-3376846           -Spray Arm Seal
343923-1-S-Whirlpool-3376846           -Spray Arm Seal 343923-2-S-Whirlpool-3376846           -Spray Arm Seal 343923-3-S-Whirlpool-3376846           -Spray Arm Seal http://www.partselect.com/Schematics/Maytag/UHLYYAGP.gif

Spray Arm Seal

PartSelect Number PS343923

This white under spray arm bearing ring is designed with the split. This is not a defective or damaged item.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Noisy.
  • Not draining.
  • Compare At

    $7.85
  • You Save

    $1.31
  • Your Price

    $6.54
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Wash Arm Bearing Ring

Part Number 402231

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

$3.61
Special Order

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 66 reviews What's this?
1-5 of 66
 

521 of 530 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: James from Jacksonville, FL

Dishes not clean and lower wash arm wobbled.

Completely removed lower wash arm and replaced bearing ring and seal.

Help other customers find the most helpful instructions.

Were these instructions helpful?

375 of 378 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Dennis from Cromwell, CT

Not cleaning lightly soiled items.

Removed spray arm thumb nut. Removed spray arm. replaced worn and broken earings and re-assembled in reverse order. Would have done the repair a lot sooner if I had known that PartsSelect was just a few miles up the highway.

Help other customers find the most helpful instructions.

Were these instructions helpful?

159 of 231 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Kent from Matthews, NC

Water washing out under front door onto floor

The plastic parts on this spray arm assembly wear with time and the rotation wobble effect creates a wave action in the pool of water at the bottom of the dishwasher. This waves the water onto the front door and forces a leak outside the unit. Replace the lower arm assembly, washer, bearing and nut. They all wear. Also remember to tighten the screws on top of the pump assembly. They loosen and aid in the wobble. Good Luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?

136 of 206 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Robert from York, PA

Lower spray arm was not turing properly and causing poor wash results

I noticed the upper bushing washer was worn thin. this caused the lower spray arm to rise too high and wobble during all the wash cycles. Also the rotation of the lower spray arm was wearing grooves in the lower bushing.

I removed the retaining nut and simply replaced teh defective parts. While I was at it I figured equal wear might be evident on the upper spray arm so I bought a complete rebuild kit to bring all rotational parts back to new and equal preformance that was achieved by removing the ss screw and removing the upper spray arm, bushing and clip then replacing them in the order of removal. Noticed a huge difference in the quality of the washed dishes!! Thanks Parts Select 100% to yoru company!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

76 of 76 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Beverly from Bly, OR

Lower wash arm was not moving freely

I first removed the wash arm retainer nut then lifted the arm assembly out and replaced the spray arm bearing ring and then set the spray arm back in place and put the wash arm bearing ring in the hole and screwed the wash arm retainer nut back in place. I couldn't believe how much the 2 had worn down. It is working fine. Saved me about a $125.00 service call out here as I live 50 miles from the nearest big town. Not bad for a 68 year old female!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 66