343694-2-M-Whirlpool-3374621-Water-Inlet-Valve-120V.jpg
343694-2-S-Whirlpool-3374621-Water-Inlet-Valve-120V.jpg 343694-1-S-Whirlpool-3374621-Water-Inlet-Valve-120V.jpg 343694-3-S-Whirlpool-3374621-Water-Inlet-Valve-120V.jpg

Water Inlet Valve - 120V

PartSelect Number PS343694

Manufacturer Part Number 3374621
Manufactured by Whirlpool

This water inlet valve is intended for use with horizontal motor dishwashers. It uses a 3/8 of an inch valve tubing and a mounting bracket.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not fill with water.
  • Leaking water.
  • Compare At

    $65.10
  • You Save

    $10.85
  • Your Price

    $54.25
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 7 reviews What's this?
1-7 of 7
 

12 of 14 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerDavid from Atlanta GA

Dishwasher running with no or little water.

Removed screws under counter holding washer in place. Pulled washer out until I could access the back. Turned water supply off (in my case faucet under the sink) Turned power off at breaker.
Disconnected water line and electrical wires noting wire location. Removed solenoid unit by undoing two screws on frame. Installed new unit, connected wires and water. Turned water on to ensure no leaks and pushed washer back under counter. Turned power back on and checked machine operation. Replaced the screws under the counter to keep machine in place. This is very easy. In my area a plumber would charge $75 to do this.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Wrench(Adjustable)

CustomerAlastair from Atlanta GA

Water inlet valve had frozen and burst

After turning off the water to the dishwasher, I used the adjustable wrench to remove the incoming water line. Then removed the electrical feed to the water valve. Lastly I removed the rubber hose on the outlet of the valve (after compressing the retaining clip) before removing the one screw that held the valve to the lower frame of the dishwasher. Once the new part arrived, it was simply a matter of reversing the above procedure to install the new part. Took under 15 mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench set

CustomerRichard from North Las Vegas NV

My wife said no water coming to dishwasher!

i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1 because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerJudy from Macomb MI

Dishwasher working with no water coming in

Turned off water and electrical. Removed kickplate at bottom of dishwasher. Unhooked water line, electrical plug and unscrewed valve from frame, noting proper position of valve for new install. The only delay we had was removing the old water line fitting from old valve. We needed the old fitting for the new valve. We solved the problem by soaking valve in boiling hot water to help loosen the connection. Install of new valve was reverse of the removal process. My son did the work and saved me approximately $200 for a service call. I also want to say that ordering the part from your company was less expensive than if I had ordered it locally and gone to pick it up! Your website is extremely helpful, user friendly, and I am recommending it to all my friends when they need to repair an appliance. Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMichael from Golden Valley MN

Water inlet leaking

Removed and replaced leaking water inlet valve, 10 minutes and saved me a hundred in plumber fees.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerCarrie from No. Miami Beach FL

Dishwasher wasn't filling with enought water to clean dishes.

We read your help site and was able to find what was causing our water filling probelms. Order the valve intake part and made the repair and the dishwasher works like new. You saved us a repair bill from the professionals and they couldn,t done a better job. I will recommand to site to everyone. Thanks Again

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve - 120V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set, Wrench set, Wrench(Adjustable)

CustomerWilliam from Rolla KS

Wouldn't let water in dish washer

unhook electric & unscrewed 2 metal screws unhooked water line,& replaced new one & reversed hooking up all it worked fine

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7