Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS343094
The dishrack kit comes with the dishrack, rollers, adjustable tines, and clips. Must be assembled.
Note: This part has been redesigned by the manufacture. Blue is no longer available. White ONLY.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Replaced the dish rack.Removed the retaining clips on the front of the rail and removed the old rack. Removed the spray arm assembly from the old rack.Assembled the new rack, with the supplied parts from the kit. Using the old rack to know where some parts needed to be placed.Put the spray arm assembly on the new rack.Inserted the new rack into the railsReplaced retaining clips.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Easy. only one little trouble spot. but very easy " repair" for the lower rack. take out of box. place in dishwasher. pull old center spindle part off by twisting 90 degrees and put into new rack same way. When replacing the top rack. keep the old one in one piece till you put together the new one. mine didn't come with any instructions. pretty simple anyway. but no problem when you can use your old one as a guide. once you put it together the only hard part i had was right at the end.. figures right!! last piece.. but to snap back in the center unit the spins around into the new one took alot of force. but it went. thats it...
Repair went OK but there were no instructions at all. Just boxes full of parts. Otherwise,assembly went smoothly. The dishwasher works like new. ( I feel that the parts were way over priced)
Took the old wheels, and other parts from the old racks and installed them on the new. The wheels on the lower rack just snap on. Also the folding tines just snapped on. On the upper rack the brackets that hold the wheels have two screws that hold the bracket. I removed them and then installed the bracket on the new rack in the same position as on the old one. The only hard part was getting the old spray arm off the old rack. I had no directions so I had to figure it out for myself. I finally cut the the old rack to get the pressure tower off. It was stuck because of having been in place for more than ten years. Putting the tower and the arm on the new rack was no problem once I had it removed. Total time to do the job about 45 minutes.
Took out old rack by twisting the rack supports. Used old supports because in good shape. Removed the wand from old rack and placed on new rack. Then replaced the supports. Worked great.
It was simple just took out the racks and used them as model. Placed new rack side by side, opened bag and laid parts out for new racks. BY looking at old it was easy to put together. New racks work like a charm.Thanks for being there it saved me having someone come out and/or just buying a new one when ther was nothing wrong withthe old one.
quick and easy replacement, without tools...i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....excellent service...
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.
Well, I tried to 'splain in upper box. Wrong rack came, your c/s guy was A++, sent me a pp return label. The replacement was here the NEXT DAY!The only problem I encountered was that the wire used to make the replacement was slightly smaller than original. The pipe-jet that forces the water up to the top rack would not stay on. I fixed it by drilling 4 holes in the old pipe-jet and used cable ties to hold it in place. This would be a problem for a person with no creative skills. This is a problem that you may need to bring to the attention of your vendor OR you could include a new pipe-jet thing that would lock on the new, smaller diameter wire. On your side, customer service and response to the shipping error was an awesome experience, apparently the Lady taking the first order mishandled. I can't tell you how professional and responsive your guy handling my "it's the wrong rack" phone call was. He admitted the error and FIXED IT, proper rack was here in North FL the next day. I just love it when companies DO THE RIGHT THING, I bet your competitors would have tried to make it MY problem. WELL DONE!
Unable to solve problem as the rack did not fit even though it was for a kitchen aid dishwasher. Returned it as it did not fit our model
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.