343074-1-S-Whirlpool-3369769           -Door Panel Insert
343074-1-S-Whirlpool-3369769           -Door Panel Insert 343074-2-S-Whirlpool-3369769           -Door Panel Insert 343074-3-S-Whirlpool-3369769           -Door Panel Insert

Door Panel Insert

PartSelect Number PS343074

This panel is reversible, black on one side, white on the other side.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $17.83
  • You Save

    $2.97
  • Your Price

    $14.86
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 11 reviews What's this?
1-11 of 11
 

11 of 13 people found this instruction helpful

Parts Used

  • Door Panel Insert

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customerstephen from west islip NY

Door insert all scatched up

Took me a while to figure out that the bottom plastic strip is all that holds in the panel. Once it is removed , it pulls out easily When the new panel arrived,just slide it up into the top grooove, and push the bottom strip back into its groove. The front looks like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerGeorge from Denville NJ

Door panels and trim damaged by power wheelchair

I removed the four screws, two at the bottom and two at the top, of the lower access panel and removed the broken assembly. I removed the piece of rubber trim from the bottom of the door panel (unsnaps from it's channel). I pried off the damaged bright trim from the left side of the door, scraping off most of the glue residue with a knife and finally cleaning the rest with solvent. I cut the new piece of bright trim to fit with siscors and pressed it in place. I used the remainder of the new trim and a piece cut from the old damaged trim previously removed to trim the lower access panel. I carefully removed the insulation from the old access panel and installed it in the new access panel with double sided tape. I followed the instructions that came with the new panels and installed them in the door and access panels. I reinstalled the rubber trim in the bottom chanel of the door. I moved the other parts from the old access panel to the new access panel and reinstalled the new access panel assembly with the four screws removed earlier. Finished...
I found other sites with the parts but ordered from PartSelect because your site made it easier to identify and select the right parts to order. My order shipped very quickly and everything arrived perfectly. I'm impressed. Thank you...

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRosalba from Brooklyn NY

Replaced door panel insert

All I had to do was remove old door panel and retainer and I replaced with the new.
PartSelect were great. I highly recommend you guys.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Door Panel Insert

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerLuann from Springfield MO

Front panel of dishwasher was dented

Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerGail from Mayville WI

Door panels looked old/bad

Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDan from Front Royal VA

Door panel was damaged and the cover over the buttons was torn.

Label cover was glued on and you simply pull it off and replace it with the new one. That takes about 2 minutes! The front panel was dented and all you have to do is pull off the rubber trim on the bottom and replace the panel. The dishwasher looks new!!

thanks
dan

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 13 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerCristen from Richmond VA

Missing front panel

Purchase new filler panel, new outer panel, and gasket to hold panel in place. Secure gasket to dishwasher frame then insert new panels.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Door Panel Insert

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerConstance from Sonoma CA

Changing a damaged door panel insert

I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerBelinda from Calunet City IL

Color didn't match updated look

First I removed the the rubber sides. Then I slide the replacement panel over the exisiting one. That's it no other tools were needed. I didn't even break a sweat.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Door Panel Insert

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerCrystal from Bowman GA

Front door panel was missing

I removed the cardboard insert, put the new front panel on and replaced the tabs. That was it!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

  • Door Panel Insert

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMarjorie from North Grosvenordale CT

Didn't look good with the new big panel changed.

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11