| |
16 of 17 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerJohn from Saint Clair Shores MI
Original timer knob was plastic construction , twisted apart
The repair was very easy. The original dial was a poor design and did not hold up to the twisting and finally let loose. The threaded bottom of the dial stayed on the threaded shaft, so it was a simple matter of grabbing it with nose pliers and spinning off. Glue does not work with this type of plastic, I tried instant glue and hot glue. The replacement part was re-designed with a metal threaded center, so when it arrived in the mail, 3 days after online ordering, I spun it onto the shaft and job was complete. While I waited for the new part to arrive, I threaded 2 nuts onto the shaft and tightened them to each other to give me a temporary 'knob' that I could grab with my nose pliers.
|
6 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerchuck from burke VA
Old knob broke off
new knob is made of metal and the old one was made of plastic. i doubt the new one will break
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
CustomerDennis from Newton Centre MA
Plastic timer knob broke
Screwed in metal replacement knob. It fit perfectly.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTammy from Elgin IL
Knob broke
Ordered part and within 2 days it arrived. Removed broken knob and twisted new one on. Awesome job getting the part to me so fast. Thank you!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerBarbara from Augusta WV
The on/cycle select knob broke into pieces in my hand
Received the new knob and screwed it on. The new knob is metal inside instead of plastic like the old one. It fit perfectly and I couldn't be happier. Also - I ordered the knob and it came in 2 days. Very effecient service.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
Customerken from central point OR
Broken timer knob and lid bumper
the timer knob shaft must be held in place from spinning while the knob hub is removed, simply grasp the shaft with needle nose pliers below whats left of the hub and with another pair of pliers grasp what is left of the knob hub and rotate counter clockwise, once it is broken free it should spin right off. Reverse this process to install the new timer knob.
Installing the lid bumper is simple just pull out the old bumper with needle nose pliers and start the new bumper in from the bottom of the lid and work bumper until the bumper clears the hole in the lid, you may need a small flat screwdriver to work it in gently as not damage the finnish or the bumper when you clear the thicker part of the bumper flange it will lock right into the lid.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerHITOMI from Laguna Niguel CA
Timer knob broke.
The new replacement part arrived in a few days. It was very easy to replace the timer knob. The photo on the website with the scales behind the product assured me I had the right part.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerBaudelaire from Morganville NJ
Washing machine only works in rinse cycle and stop at end of cycle. It agitates but does not spin
I made sure timer knob was pushed in. I removed old timer knob and noticed a piece of it was still attached. I removed the old plastic piece and screwed in the new knob. Job was quick and easy
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerJames from Carrollton TX
Broken timer knob
Removed the half of the plastic threaded knob with a regular pair of pliers. Just screwed the new knob on.Which by the way is all metal threads so this problem has gone away
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:Less than 15 mins
Tools
CustomerDebbie from Centennial CO
The part I needed was discontinued due to the age of the washer.
I applied liquid nail to the bck of the knob,screwed it on, and left it untouched for 24 hours. Now, it works perfectly.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMaribel from Los Angeles CA
The cycle knob broke
I removed the old piece and replaced it with the new one. It was the easiest repair I've ever done. The website was super helpful with diagrams and tips and made the experience of buying the part as easy as repairing it!!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWilliam M. from Jacksonville FL
Plastic knob broke
As simple as opening the mailer, walking to the machine and screwing the new knob on. Original know had plastic threads, whereas the PartSelect replacement has metal threads. Fair and reasonable price, simple - no hassle ordering process, prompt quick delivery and my wife is a very happy person again!
|
21 of 667 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerGary from Sherman TX
Timer knob missing
Installed new timer knob on timer shaft and it worked as expected.
|