342434-1-S-Whirlpool-3363394           -Direct Drive Water Pump
342434-1-S-Whirlpool-3363394           -Direct Drive Water Pump 342434-2-S-Whirlpool-3363394           -Direct Drive Water Pump 342434-3-S-Whirlpool-3363394           -Direct Drive Water Pump http://www.partselect.com/Schematics/Whirlpool/YDVXUGRU.gif

Direct Drive Water Pump

PartSelect Number PS342434

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Will not drain.
  • Pumps but will not spin.
  • Fills and drains at the same time.
  • Noisy.
  • Leaks water.
  • Will not fill with water.
  • Compare At

    $30.71
  • You Save

    $5.12
  • Your Price

    $25.59
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 195 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Direct Drive Water Pump
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Patrick from St. Clair, MO

The pump was cracked

Simple. Removed two hose clamps, pulled off the hoses, removed the clips that held the pump in place and removed the old pump and then simply did the same thing in reverse to put the new pump in. It was easy and the pump was an exact match.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Direct Drive Water Pump
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Romeo from Milpitas, CA

Water leak on the water pump

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Direct Drive Water Pump
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Nathan from Oceanside, CA

Pump went bad, direct drive washer

the hard part was getting the pump off of the rusted centerpeice. i actually had to grab the pump with both hands, put my feet on the rotator and PULL. finally it basically snapped off and rusted peices went flying. after cleaning it the new pump went on rather easily, with the help of a rubber mallet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Direct Drive Water Pump
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: James from East Hanover, NJ

Water leak in front of the machine.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Direct Drive Water Pump
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Chris from Summerville, SC

Leaking pump

Luckily this washer was in the garage and was being made ready to replace an old broken washer. Being able to lay the washer on its side made the job much easier than if it was upright in the laundry closet.

Removal of the old pump was simply a matter of releasing the two clamps holding the input and output hoses and removing the two spring clips holding the pump in place on the motor shaft.

The new pump install required a reversal of the above and took about 3 minutes. It was a very easy and successful repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?