This part is able to sense the water level in the tub. When the water reaches the desired level, this switch stops the water from flowing in the tub and the washing program begins.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Whirlpool, Estate, Roper.
Part# W10335056 replaces these:
AP4566382, 1617123, 3366846, W10335056VP
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
5.0
Filter By Rating:
5 Stars
6
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Marlyss B - October 1, 2022
Verified Purchase
Water level switch.
Took minutes to install & works great.
★★★★★
★★★★★
Michael L - July 27, 2021
Verified Purchase
This was an easy repair
The part was in great condition and arrived quickly. My washer is up and running again. Thanks so much!
★★★★★
★★★★★
Mark L - October 16, 2019
Verified Purchase
With Youtube easy repair part was spot on.
Part came in a few days, Perfect condition works great I will buy from this site again
★★★★★
★★★★★
HOUSTON H - August 8, 2019
Verified Purchase
easy to repair work great
part work great ,part came fast.
★★★★★
★★★★★
LARRY E - July 10, 2019
Verified Purchase
Easy repair
Part was exact replace and worked great
★★★★★
★★★★★
Arnold K - January 1, 2019
Verified Purchase
very easy install
worked perfectly
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 6 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No water was coming into the washer
Before I start, I should clarify that before I replaced the water level pressure switch I replaced the water inlet valve (aka solenoid). Past experience had taught me that the solenoid was a likely cause, I never thought about the water level swtich. Replacing the solenoid was 75% of the time involved, only because I had to disconnect hos
... Read morees and figure out how to get to the solenoid. When that didn't solve the problem the likely culprit was the water level swtich so I didn't even test it I just changed it. I'm not sorry I replaced both parts. The gunk that had blocked the filters to the solenoid would have caused problems soon anyway. Replacing the water level switch took 15 minutes or less because it was so easy to access. Washer loads fine now!
Read less
Richard from Russell, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
11 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water did not shut off at water level setting
The replacement switch arrived exactly on the number of days I was advised when I ordered it. After opening the lid of the washer, the old water level switch was turned 1/4 turn, and it pulled right out (after unplugging the electical wires from the switch). I replaced the rubber water tube ann plugged it into the new water level switch
... Read more. Then installe the switch, and closed up the washer. Not hard at all.
Read less
Ronald from Richboro, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
6 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not fill with water
Tried replacing the water valve first (85% - this is the problem... from the website)... It did not fix the problem. Ordered the water level switch (10% - this is the problem... from the website).. It works like new. The website had lots of information, videos, specs, etc. It really helped a lot...!! Feels good to fix a washer
... Read more that did not work... Thanks partselct.com...!!! -Eddie Campbell, Charlotte, NC
Read less
Eddie from Charlotte, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water was overfilling
There was a hole in the tube that connects to the water level pressure switch...so we could have just bought a new tube but we replaced the whole thing anyways. This job was easy up until we had to take the hose out and we had to remove the back cover. But works great now =-)
Fely from el cajon, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
9 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer shot--possibly the switch also
Was not aware that the pointer on the dial could get way off the slot it was supposedly pointing to. It has taken numerous run throughs of the wash cycle to get it close. It would point to rinse but actually it was on OFF or on wash when it was really on spin. I am not certain how this could be remedied since this timer was new and set
... Read more on who knows what when it was installed.
Read less
Claude from Highland, UT
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
0 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water control would only fill to Medium load then stopped altogether
I removed the screws holding the control board in place. Removed the knob on the front of the panel and then disconected the wires to the control. Then I took the old control off the board and inserted the new control. I attached the wire connectors to the new control and put the control panel back in place and fastened it with the scr
... Read moreews. Last task was to replace the knob. The new control worked wonderfully with the first load of laundry. Piece of cake. Done in 5 minutes or less.
Read less
Wayne from University City, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
25 of 33 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melanie
February 22, 2020
Having problems with water level knob turning. Do i need a new water level pressure switch and knob? What part would i need to buy?
For model number kenmore 11028352700
Hello and thank you for writing.
Yes, you do. You might be able to use the old knob as the problem is most likely coming from the switch itself. We hope this helps. Please contact us anytime if you require further assistance.
My washer does not fill more than the low level even if i pick the high level setting. Do you know what part i would need to fix this problem.Thanks for any info
arnold
For model number 110.28882790
Hello Arnold, Thank you for the question. I suggest checking the tube that goes to the Water Level Pressure Switch. Make sure there is no clogs or blockage. If the tube is good, you may need to replace the switch, PartSelect Number PS3408073. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
James
September 23, 2019
I need a water level switch and knob for my Kenmore 600 washer, model 11029692800
For model number 11029692800
Hello James, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3408119 for the switch and PartSelect Number PS11752937 for the knob. Hope this helps!
When i turn my Roper on it agitates but won't fill up until i mess with the water level switch i think the switch is bad but i want to be sure before i get a new one
For model number Ras8445kq0
Hello Richard and thank you for writing.
It certainly sounds like it could be a faulty water level switch PS3408073 and/or a faulty PS334646
, you should check for signs of damage, and replace it if necessary. We hope this helps. Please contact us anytime if you require further assistance.
Hi, Can you please give me the parts number replacing water level switch #3366848. Thanks
For model number 11024662300
Hello, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11723158. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
