http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/54093.gif
See part 15 in the diagram

BAFFLE

PartSelect Number PS3406519

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not draining.
  • Leaking water.
  • Compare At

    $4.58
  • You Save

    $.76
  • Your Price

    $3.82
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

71 of 145 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set

CustomerChristopher from Chruchville MD

Dishwasher would not pump water out. Othre appliance was advantium oven.

Removed the dishwasher. Simple to remove and replace the pump, flapper, and o-ring. Reinstalled dishwasher. It worked!
The GE Advantium was another story. Replaced the Magnetron, diode, and capacitor. Oven still did not work so I took it to the dump. No more GE!

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 22 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerBrian from Keokuk IA

The dishwasher would not drain

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerJohn from Carrabassett Valley ME

Dishwasher wouldn't drain.

It was very simple. My neighbor, whom I call Tobias Maintenance & Repair, did all the work, while I watched with a glass of Jack Daniel’s. The pump twists into place and is held by two small bolts. It's very easy to get to and nothing else needs to be taken apart or disconnected. Used some silicon sealant to hold in place after replacing the pump and all seems good again. The pump was the problem and the dishwasher now runs fine.

However: The Float Assembly I thought I ordered was not the one I received. Also the pump drawing did not indicate that I would not require O-Ring Drain Pump, so that was ordered. My request for return information has been ignored. Please send me $8.80 and I’ll call it even.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench set, Wrench(Adjustable)

Customerjohn from ramsey NJ

Water leak from drain pump area

after removing dishwasher from cabinet I discovered a crack at the right rear mounting boss of the tub, Unfortuneatly this was My fault as I was careless in My leveling procedure during the install 3 years in the past.
Bottem line, Replaced unit with stainless steel model $700.00
Will pay close attention to install instrustions

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4