Top Burner Spark Ignition Electrode with Retaining Clip

PartSelect Number PS338500

This part helps your burner ignite and produce flame.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Gas igniter glows, but will not light.
  • Element will not heat.
  • Compare At

    $24.17
  • You Save

    $4.03
  • Your Price

    $20.14
In Stock
Order within the next 10 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 4 reviews What's this?
1-4 of 4
 

17 of 24 people found this instruction helpful

Parts Used

  • Top Burner Spark Ignition Electrode with Retaining Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBilly from Martinsville IN

There was a crack in the porcelain not letting it spark

I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

  • Top Burner Spark Ignition Electrode with Retaining Clip

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerJoe from San Bruno CA

Broken ignitor insulation; repeated sparking after burner lit

Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used

  • Top Burner Spark Ignition Electrode with Retaining Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJanie from Montrose CO

The ignitor? Would not spark to light the burner.

First I unplugged the electric line to the range. Then I removed the screw that holds the burner in place and then lifted the burner up. Pulled the elec line off it and then took the ignitor/sparker? out of the burner. inserted the new one and put the elec wire to it. screwed it back in place and turned on elec and tried the burner. But now it sparks sometimes and sometimes not. And only if holding the gas on longer than I want as it stinks up the kitchen and is dangerous. What else does this burner need to work properly?

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Top Burner Spark Ignition Electrode with Retaining Clip

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerWade from Jacksons Gap AL

Spark ignition electrode was not sparking properly

Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4