http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/MZRNG7WD.gif
See part 9 in the diagram

Agitator Cam Kit

PartSelect Number PS334648

This kit included the cam, 4 dogs and bearing.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Unusual Noise.
  • Pumps but will not spin.
  • Shakes and moves.
  • Compare At

    $9.68
  • You Save

    $1.61
  • Your Price

    $8.07
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Agitator Directional Cogs

Part Number 388034

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$3.32
In Stock

Cam Driven Bearing

Part Number 350976

$4.60
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 59 reviews What's this?
1-15 of 59
 

46 of 50 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

Customershawn from la jolla CA

Dog ears worn down; upper agitator not moving

Pulled off the dispenser. Used socket set to remove bolt. Removed entire agitator out of washer. Placed both feet on bottom of agitator and then pulled up on the upper agitator. It took some muscle due to the years of washer use. I used a flat-head screwdriver to weaken the plastic clips holding down the old bearing-driven cam. Once I got the upper agitator off, the guts were easy to pull out. Then I just re-assembled with the 3 new parts (the Cam Driven, the Dog Ears, and the Bearing-Driven Cam).

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 20 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerJeffrey from Williamstown NJ

Agitator was skipping, making grinding noise

The repair was easy, first you take out the fabric softener dispenser, you will then see a plastic cap at the bottom. the plastic cap pulls right out. Once you remove plastic cap you will see the top of a 11mm screw. Use an 11mm socket with 6 inch extension to remove the screw. The screw is a fine thread so it takes alot of turns to unscrew. After removing screw the whole agitator should pull out of washing machine. The agitator has two parts, lets just say a top and a bottom. Once out of the machine turn the agtitator upside down and tap the top part with a rubber mallet, it will fall off easily and the cam will come out with it. Once you have done this you will see how easy it is to replace the cam and put everything back together. My washer works like new. my only trouble was finding the part, until i found this web-site Part Select, The Whirlpool site did not even offer a diagram for my washer. So thank you Part Select from me and coworkers for the part and fast delivery. I can now wash my clothes again. Yeah !!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerRichard from Houston TX

Agitator would not spin

replaced the agitator cogs, bearing and the O-Ring. I looked all over Houston for these part, but found them on PartSelect. Had them in about 3 days. The repair only took about 30 minutes.

I saved a bunch of money!!
Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerKenneth from Valencia CA

Teeth on the agitator cam were worn down, so would not agitate.

On my Whirlpool washing machine I first pulled off the top cap piece of the agitator. No clips it just popped off.
Second I reached down inside the agitator and pulled straight up on a dome-shaped piece that was a little difficult to get out but it has two metal handles that allowed me to hook my fingers around it. Once I pulled hard enough it came out.
Third I used my left hand to hold the base of the agitator still while using a socket to break lose the big nut down inside the agitator. After getting the nut off I pulled straight up on the base of the agitator and pulled the whole unit out of the washer. Here's where I got stuck. I wasted about 45min trying to pry open the little plastic tabs down inside the agitator that hold the cam in place. What I finally did that I should have tried first to step on the base with both feet and pull up hard on the agitator cylinder (that has the spiral fins on it) at it popped off and popped off the cam at the same time. After that reassembling everything with the new cam was straight forward (just reversing all the steps).
I hope this helps you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerMarcellia from Ashland KY

Top part of agitator broken

Removed the softerner dispenser and the inner cap and seal. Removed the mounting bolt. Pulled on Auger and entire agitator came out. I needed to separate the parts. It said to stand on the bottom and pull on the top. I am an "older" woman and after wrestling with it for an hour without success I waited for my nephew to come by to separate the two pieces. When he did, it popped apart and all the parts went flying. Poor guy thought he had broken it. After conviencing him that that was what I wanted it to do, he left. Dirrections weren't very clear as to what went on first and I didn't have the convience of seeing it before it flew apart. Finally put it together and replaced the bolt. To no avail, something was wrong. My sister was making the same repair at her house across the street so we double teamed it. She came over and told me that I needed to put the Bottom agitator in the machine, then the spacer thrust, then the auger, then the assembled cam and cam dogs, then the bolt. All went well and was working.......so we thought. Started a washer load and the washer started leaking water. Don't know why, still don't know why. All I did was remove everything, put it back the very same way, and it hasn't leaked since. Go figure!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerBecky from Oskaloosa IA

Pump leaking, agitator not turning

First I went to this site and read what everyone had to say on leaking pumps. After finding the model number, I looked at the parts list, and found what parts I thought I would need. First I shut off the water and unpluged the washer Replacing the water pump was very easy after reading what other people had done. I pulled the washer out from the wall about 18 inches and tilted back on a 45 degree angle. The pump was now in plain sight and helt in with two slide clamps. Using a pair of plyers I remover both clamps from both hoses on the pump. By pushing to the outside of the pump I was able to remove both of the slide clamps. This allows the pump to be lifted out and off the motor shaft. As my washer had just started leaking " about one week" the pump slid off the shaft easy. There was no rust on shaft. Pump shaft has a slot in it so the pump can only go on one way. By reversing the way I removed the pump I was able to slide the new pump back onto the shaft and slide the slip clamps back over the pump. Replacing both hoses and both clamps. Now pump was in place. I pulled the washer away from the wall and slid back into place. That took care of the pump. For the top side I removed the top part of the agitator by pulling up and removing the part that holds the softner. Under this was a piece of plastic that I was able to lift out. Under that was a 12MM bolt with a rubber washer. Using a scoket set I removed the bolt and washer. Lifting up on the agitator it came right out. Pulling on each end of the agitator I was able to pull it apart. Inside was a large plastic washer and agitator directional cogs all in one piece. This piece just lifts up and off. I replaced the old piece with the new on and slid the two agitator back togeather. Setting the agitator back into the washer and put the 12mm bold and rubber washer back on. Then I put the plastic back on and set the top softer cup back in place. Snapping in the bleach dispenser was very easy, just shap into place. Pluging the washer back in, and turning back on the water I ran the washer with no clothes in it so I could check for leaks and make sure everthing was working. Repairing both parts took about 30 minutes and now the washer is like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerChrista J from ElDorado Springs MO

Agitator noisy and water level wacky!

Observing where the problems were coming from, easily found the parts, thanks to Parts Select s super helpful site. Got parts the very next day! Wow better than any repairman could do! Took less than 15 minutes to put the new parts in. No hasle and super easy as I am NO repairman when it comes to appliances but I can fix just about any appliance now that Part Select is there to help in time of need. Dont waste your time or money on warranies that are fruadalent nor the old rip off repairmen of this day whom are for their own gain only. Any one can fix appliances through this site. I am grateful to have found this site and thank Part Select for their interest in helping people....

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers, Socket set

CustomerFrank W from Brooklyn Park MN

Upper agitator wouldn't spin

Removed the liquid softener cartridge.
Removed the plastic seal inside the upper agitator using a pliers.
Removed the bolt holding the agitator in place using a 7/16 socket wrench with a 6 inch extension.
Lifted the agitator out.
Separated the upper and lower agitator into two pieces.
Replaced the cam assembly inside the upper agitator.
Reversed the whole process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerErika from Columbia TN

The top of the agitator wouldn't turn, just the bottom

I removed the softener cup, unscrewed the bolt and replaced the cam kit. Super easy just like everyone else said. Parts were here very quickly and at a great price!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerJOHN from MIDDLETON WI

The agitator was no longer agitating the clothes.

First I pulled the liquid softener dispenser from the top of the agitator. Then I pulled (also by hand) the cover that was beneath it. That revealed the bolt holding the agitator in place. I loosened this with a socket set and removed it. The old Cam-Agit, which was stripped, popped out and the new one popped in. I then reassembled everything in reverse order and was done in approximately 5 minutes. The agitator works great now and we are no longer getting clumps of powder detergent in the clothes from lack of agitation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set

CustomerLincoln from Chicago IL

Agitator wasn't moving

Much like the other descriptions. I found the video helpful and this was the only vendor that had diagrams, so you could see how things went back together. When I popped off the top piece, everything went flying, as someone else mentioned, so the diagram was essential.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerStephen from Stansbury Park UT

Top half of aggitator was not moving.

Replaced agitator cog/clutch unit under the softener dispenser. It is the second time I've replaced it in the last 3 years, maybe it has been loaded too heavy, I'll have to have that talk with everyone else on the family who does laundry.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerNick from Castro Valley CA

Agitator slipping

Removed bolt in center of agitator then slid agitator straight up and out replaced the dogs and the other parts that came with the cam kit i also replaced a few of the other parts that wear in the agitator ,you can actually re-cut the teeth on the dogs with a razor so that they will work again ,but new parts are very reasonably priced and the parts arrived very quickly the next day .

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerPhyllis from Reidsville NC

Top portion of agitator quit turning

Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Agitator Cam Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerLawrence from Dundalk MD

Agitator was free spinning

Followed instructions, which were included with the parts, and the repair was a snap. So easy a caveman could do it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 59