| |
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerPhyllis from Reidsville NC
Top portion of agitator quit turning
Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Socket set
Customerjimmy from southport FL
Top agitar dogs failed to grip anymore,just worn
pulled the new ones out of package,same part nice instructions,couldn't get any eaiser,thanks guys for the very fast shipping
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
Customerscott from west covina CA
Top part won't turn by it self
pull the top cap off, then the inner cap off, then use the 10mm socket to remove the nut., then pull the whole thing off.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerMichael from Watson AR
Worn cogs, machine would not agitate.
Well, I took out the worn parts, replaced them with new ones, end of problems. except that I did not see in the parts book where the new agit came with new cogs . So, I wound up with an extra set of cogs (at my cost). Gotta say one thing though, the service was good and fast, even though it was during christmas holidays. Thanks.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerLYNN from Midlothian VA
Would not agitate on the top portion of agitator
Removed the softner dispenser and lifted up the plastic piece under that. Used a 9/16th socket with a long extension and unscrewed the center bolt.
Lifted the entire agitator parts off and out.
Next had to get husband to separate the top from the bottom, it was really hard for me. I am a woman but not weak!!
Replace the washer and the other 2 parts, and put it back together and it all took about 15 to 20 minutes.
Easy repair, even for a woman!!!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
Customersteven from san clemente CA
The top part of the washer was not ratcheting to turn clothes over in wash tub
removed the softner insert, pulled the plastic seal, loosened and removed the 7/16" bolt that holds the paddles in the tube. removed the top part of the paddles/agitators, removesd the old cams and replaced with the new. it works awesome.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerDuane from South Deerfield MA
The washing machine was making a loud noise
I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerLinda J. from Salisbury NC
Agitator wasn't working properly
Watched the PartSelect video and it was a help, but it stated to throw away the old bolt and install the new, but it wasn't inclued in the Cam kit and wasn't told when ordering that it should be replaced. Still don't understand why. Took the opportunity to REALLY clean the agitator inside and out of soap scum. Just about soaked off with Scrubbing Bubbles in the shower! PartSelect had the parts we needed at a much less cost than the major stores. Thank you!S
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerRonald from Vancouver WA
Fabric softner and agitator not working
it was easy to repair with the instructions that were included. the agitator dogs was not allowing the fabric softner to work correctly so by replacing the agitator dogs the fabirc softner now works with no hassles. I replaced the fabric softner part as well.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
Customermatthew from alton IL
Agitator was not turning
I removed all center plastic pcs. by pulling them out by hand. No tools required until you get to nut, unscrewed nut counterclockwise and then pulled straight up on agitator. Set it on the ground and replaced worn parts. Reversed setup to put back together. P.S. Agitator snaps on and off, it takes a little force ..........AFTER NUT IS REMOVED OF COURSE.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerJoseph from Goose Creek SC
Top agitator not working
Removed agitator. (nut under softener dispenser) that pulled top of agitator off and removed and replaced Cog assembly. Reinstalled agitator.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerKenneth from Walla Walla WA
Original agitator "gears" were worn making the rotation / agitation work poorly
When the parts arrived it was relatively easy to remove the entire agitator system with one socket through the top of the molded plastic. The new parts were exact fit (even exact color) so repair was fairly easy.
Once the bolt is removed allowing removal of the entire agitator, the remaining parts come apart without tools. The only problem is if the new part comes apart. The "gears" can be put in backwards not allowing for the proper agitation.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Socket set
CustomerChuck from Marrero LA
Agitator would not turn.
Went to website and found question to what problem i was having with washer and they gave me a list of parts to fix it. The video that showed me how to change the parts was very helpful. I replaced the Agitator Cam Kit and the thrust washer. It was very easy to do and watching the video before i started helped.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsSocket set
CustomerHENRY from GRIMESLAND NC
Cams on cloths mover where stripped
removed the old parts and replaced with new ones it was simple parts were a perfect fit
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerCharlie from Lockney TX
Uper agitator not moving
after i got the part... problem with fedex in my area had the washer going before the truck drove off. Very good instrection thanks
|