60 of 243 people found this instruction helpful
Level of DifficultyEasy
Time to do repair:More than 2 hours
ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
CustomerFrancis from Ann Arbor MI
Drum and agitator did not turn and machine squealed.
As best described in the clutch DIYs, removed the enclosure, unclipped the water pump, motor and elec. harness to check the coupling. The bushing separated from the plastic fingers which caused the squealing. Checked the gearbox and it turned for a limited amount before jamming. Ordered new gearcase and clutch (since it was over 10 yrs. old.), and a coupling. (Gearcase comes with half a coupling, so check if req'd for motor shaft.)
For ease of removing and re-installing the motor it is best the machine lays on its back. This way the grommets and coupling can be easily aligned on the face-plate without having to manually support the weight of the motor. In the tub, unsnap two agitator caps. The inner one has no tabs to break so pry and pull on the "ears". Use 7/16" socket wrench with extension to unscrew the bolt holding agitator to gear shaft end. Assuming the motor and face-plate are still off, unscrew the three screws holding the gearcase in place and slide it out. Before installing the new clutch onto the new gear shaft, slide the plastic thrust spacer? (in kit but not shown in any instructions) down the shaft, observing which is the correct side. Check for correct clutch spring, as per instructions. Slide clutch, open side up, down the shaft. Instal wire retainer (this can be tricky) and circlip. if the brake assembly slid down while sliding out the gear shaft, squeeze its spring with a pipe wrench and push it back up (with rubber mallet). The clutch kit comes with a plastic pawl? which mounts under the brake and mates with the clutch. If the locating pins for the old part are broken off, drill them out of their holes so the new part fits snug. Insert the gear shaft up the brake sleeve into the agitator so their splines mate. Screw gear case to its mounts, agitator to shaft end (not too tight here) and snap on caps. Screw on face-plate, replace coupling on motor shaft (if req'd.), set motor on face-plate, aligning the coupling and checking the grommets fit in their holes. Instal motor holding clips (with screws), mount water pump with its holding clips, and wire harnesses. Stand up machine and replace enclosure, back panel and hoses.
Replacing the gearcase was easy. Because of space limitations, removing and replacing the enclosure, etc. was a b**** that took most of my time. And watch the lid doesn't fall on your fingers!
45 of 1232 people found this instruction helpful
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerDavid from Goodlettsville TN
Machine would not spin
Disconnect electrical, took out agttator, tipped machine againest the wall. On hooked the two hoses on pump, removed three bolts pulled complete assembley out removed worn parts and installed new parts and reassembled. Works like new,
41 of 1227 people found this instruction helpful
Level of DifficultyA Bit Difficult
Time to do repair:More than 2 hours
ToolsNutdriver, Screw drivers, Socket set
CustomerNeal from Howell NJ
2 1/2 year old whirlpool top load washer fails to spin clothes dry.
First confirmed it wasn't the lid switch by jumping. Then confirmed by taking off washer cover that the transmission was leaking and spraying oil as evidenced by yellow oil film on the inside of the washer cover. The leaking oil caused the clutch assembly to slip and wear. Replaced both the clutch assembly and the transmission upper two seals.
To repair, after taking the washer cover off removed the agitator holding screw. Then remove two clips holding water pump. Unconnect the motor wires and remove two clips holding motor in place. Tilte washer back leaning up on a chair and remove 3 bolts holding transmission assy in place. Slid out the transmission/ shaft from machine.
I rebuilt the transmission by separating the case on bench and replacing two seals. To do this you first need to remove clutch assembly from the trans agitator shaft. The clutch is held on by a washer and two spring clips. You need to take note of the orientation of the parts for proper reassembly. The difficult part was separating the cover of the transmission from the base . After removal of the cover screws using a putty knife and hammer I gently tapped all around to separate the halves. The I replaced the two upper seals, one one the cover and one in the output shaft. The second difficult part that requires some skill is removing the seal from the transmission cover. I used a hair dryer to heat up the aluminum cover to ease removal of the seal. After replacement of the seals I resealed the cover onto the base using automotive silicone gasket maker. Note; I kept the transmission level during this repair so that I did not need to drain oil. After keeping the transmission level and allowing 24 hours for the silicon to cure I assembled the new clutch assembly and clips in reverse order on transmission shaft. Then reassembled the transmission, motor and pump in reverse order. Ran machine with full load of towels. Spin problem fixed and transmission is still leak free a week later.