Quick Question!

Have you ever purchased from PartSelect.com before?

334304-1-S-Whirlpool-279827            -Drive Motor with Pulley
334304-1-S-Whirlpool-279827            -Drive Motor with Pulley 334304-2-S-Whirlpool-279827            -Drive Motor with Pulley 334304-3-S-Whirlpool-279827            -Drive Motor with Pulley http://www.partselect.com/Schematics/Maytag/UTGT4VNQ.gif

Drive Motor with Pulley

PartSelect Number PS334304

This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, KENMORE®, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Will not tumble.
  • Noisy.
  • Shuts off too soon.
  • No heat or not enough heat.

Compare At

$144.38

You Save

$24.06

Your Price

$120.32
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 61 reviews What's this?
 

7 of 9 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Frank from Smyrna, TN

Start windings burnt out on original motor (dryer would not start)

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 8 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Customer: PHILLIP from AUSTIN, MN

Start and then kick out.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Tommy from BRUSH, CO

Dryer motor quit working

i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Anthony from PITTSTON, PA

Dryer makes squealing noise, finally the motor seized up.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: John from Wilton, CA

Dryer made loud rumbling noise and then shut down

It had been making noise for a week and I bought the two drum support rollers hoping that was the problem. It wasn't as the dryer started shutting down after a few minutes of running. I opened the top of the dryer and removed the 2 screws holding the face and door on. I removed the face and disconnected the door switch wires and released the drum belt by pushing on the idler pully. I then removed the drum straight out the top. I then put a wrench on the fan on the back of the motor and unscrewed it and then released the two holdown clamps on the motor and removed the motor. I had to make a couple of wiring modifications for the new motor but the instructions and connectors that came with the motor were perfect. I put everything back together and plugged the dryer back in and tried to start it and .... Nothing. I forgot to reconnect the door switch wires. Fixed that and the dryer now runs as good as new and makes no noise at all now (almost anyway). It should be good for another 10 years easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Dan from SYRACUSE, UT

Mother was frozen up

I followed the video. So easy..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Socket set, Wrench set
Customer: James from COTTONWOOD, CA

Motor failure

Used this resource and others' advice -thank you . Make sure to disconnect power first. I had replaced the rollers and tensioner a week earlier due to squeaking, but mine was the rare one where squeaking meant motor failure, so I had to place another parts order. The dryer was 19 years old, and my blower wheel did not simply 'unscrew with reverse threads'. During removal the blower wheel's plastic deformed, so had to do like someone else did and cut the rear shaft with a reciprocating saw. Just be careful not to damage the bulkhead's built-in bracket that anchors the rear of the motor. I think it was a 13/16" wrench that fit the blower wheel and I forget the size for the pulley nut on the front of the motor, but I suggest a deep socket since it held well. My best advice when dealing with a motor replacement is to ensure the blower wheel wheel will separate successfully from the motor before placing your parts order should it be a stubborn removal. Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: George from ARLINGTON HTS, IL

Motor would not start

follower the instructions from a you tube vid on whirlpool dryers. The connection of the motor to the blower is fairly tight be sure to turn it the correct direction, retaining clips for the motor are harder than is looks to reinstall. The new belt and rollers were a prenventive measure, If I had it apart I should just install the new belt and rollers.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Andrew from Edina, MN

Dryer stopped working.

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Charles from Traverse City, MI

Dryer would not run. Push start and only relay clicked.

Troubleshoot wiring to make sure it was'nt fuse or limit switchs. Had voltage to motor but nothing happened. Had to be the motor. Ordered motor and a couple of other parts that needed to be replaced. Motor replacement was real easy, hardest part for me was getting blower off motor shaft. Was a good time to clean out dryer and vent.Found a few dollars in lost change also, my tip. Used your regular shipping and from order to repair was only three days. I would definitly order from you again. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Wrench set
Customer: Calvin from Downs, KS

Dryer was shutting down,in 5 minutes, either heat or no heat.

Pulled back panel off, then removed entire front body. Accessed the blower and the lint cover and removed. Removed drum and belt. Removed motor and replaced, reassembled and plugged in and it worked. Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Brad from Lake City, FL

Buzzing sound while start button pushed. Then shut off after 30 seconds.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Wrench set
Customer: Chris from Randolph, MA

Dryer would turn on and imediately stop

Shut off gas and unplug dryer. Disconnect gas. Take back pannel off by removing a bunch of screws. Take lint trap apart few more screws here. Remove top of dryer (pop the plastic cllips), and front door/panel. Vacume all areas (tons of lint everywhere). Pull out tumbler. Change support wheels. Take off blower fan by using an adjustable wrench and 1/2 " wrench. hold fan with adjustable wrench and turn drive shaft clockwise. Then remove motor. Replace with new motor and reverse the process.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Raymond from Rahway, NJ

Noisey

Removed screws fastening lint catching housing. Unpluged door open switch and removed nuts on front panel. Before removing front of dryer, I bent a piece of a wire hanger into a hook and tied a string to it and tightly to the top rear panel of the dryer. I then put the hook along the top of the drum to hold it so that it could be removed easily without falling when lifting the front panel off. I then removed the drum which opened the entire internal of the dryer for viewing. Before ordering parts, I removed the belt and ran the motor to realize the motor seemed to be creating the screeching noise. Upon futher review I noticed other parts were worn. I oreded and replaced the idler pulley and drum support rollers. I then removed screws in rear of the dryer to replace the fan from the motor shaft. I realized after a few minutes that the fan attached to the motor shaft was reversed threads. I could not remove the fan assembly from the motor shaft so with a drill,I drilled several holes in the fan and cut it off of the shaft with a hack saw. I now had to purchase a fan. The installation of the fan and motor were very simple. I again used the string and hook to secure the drum while reassembling the new belt through the idler pulley and to the motor. Turned a few nuts and all was complete. It now runs as it did when it was new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Drive Motor with Pulley
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Socket set, Wrench (Adjustable)
Customer: brian from alpine, TX

Motor making strange noise

I removed the back before I relized that the motor was under the drum. I removed the front and the drum and accessed the motor. I used a small flat head screw driver to prythe brackets that held th motor in place. I had a bit of a problem removing the motor from the fan. Then I read the web site and figured out that the treading was a LEFT thread. Still had some problems and ended up removing the pully wheel and using a pipe wrench to get the fan off the motor.

I wish I had taken a picture of the pully and belt to see how it went back together, but it went back easy enough.

Very pleased with my effort and guess I saved about $300 bucks on the repair, and the 2 plus weeks to get the guy to my house.

Help other customers find the most helpful instructions.

Were these instructions helpful?