Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS334278
This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Followed video on site
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed the back cover, removed the thermal cut-off and checked with ohm reader, didn't get a reading. Ordered the part, plugged in the two wires and screwed in the two screws. Replaced the back cover, dryer works like it did the very first time. This does not take a male to do it. (No offense men). This site offers a short video on how to replace each part if you can't figure it out for yourself.
After disconnecting power cord, I removed the bottom front panel and disconnected 4 wires. I removed the screws, and the old parts, replaced the new parts, put the screws back in, and re-connected the 4 wires. One of the fuses only required one screw, and had a little clip to go into the other hole. The job probably took about 5 minutes, but I cleaned lint from inside the dryer. After replacing front panel, and connected the power cord, the dryer heats fine.
Removed the heating element and repaced it with the one that was shipped.
I am nine months pregnant and can't believe how easy it was. Took the back panel off and saw that the heating element looked fine. I checked to three thermostats and found the two that were dead. I found the two online that looked like the two i needed, ordered the parts and they came in 2 days. It was sooo easy i can't believe i actually thought about calling someone to come fix it for me.
The kit came with two fuses. On testing with the ohm meter I found the one that was bad. But of course I put in the two new fuses. It was easy to reach from the front with the lint trap removed. The fuses were easy to disconnect the wires and unscrew and then put the two new fuses in - again screw the fuses in and then connect the wires.
removed the heater element housing from the dryer. then on a table removed and replaced the thermal cut-off kit
I did this wrong and then I did it right. Without testing, I ordered a heating element, but that didn't fix the problem. I went back to PartsSelect and learned how to test the different parts of the dryer. It turned out to be a faulty fuse. Once I had the correct problem to solve, it only took me about 15 minutes.
Of course, I checked on-line to see how to do this repair first. It was the thermal cut off that needed to be replaced but there was a reason it went out. The vent had come loose behind the dryer. I didnt think that was a big deal, but the dryer sucks all that lint back into the dryer. There was an inch of lint inside the back of the dryer. It got too hot and lucky for me, the thermal cut off shut it down. Otherwise, it would of caught fire. The repair was easy and the dryer works great again. Just be sure you keep the vents connected and clean.
Used Instant Repairman to troubleshoot, discovered that no heat was solved by replacing "Thermal Cut-off Kit" and was the problem 55% of the time. Bingo, back in business. The schematic online showed the location of the parts and was fairly easy to replace once all the guards and front panels were removed, 12 screws and 3 spring clips. We are dealing with 220 voltage here, make sure to unplug the dryer and/or shut off the breaker, always double check with curcuit tester or volt meter, stay alive!
Replaced parts and now I do not need to but that new $500-800 dryer! Thanks!
I found the serial # in the door jamb of the dryer and went on line asking the question "dryer won't dryer. It was all down hill after that. I was directed to Part Select, where I input the serial number of the dryer and up popped a complete line of replacement parts to choose from. They even had videos to show me exactly where to find the parts, how to take the dryer apart, and how to remove and replace the parts I needed. Here's a link to Hubpages along with a longer story I wrote about fix the drayer:http://jeromeo.hubpages.com/hub/WET-CLOTHS-DRYER-GOES-OUT.
Checked heater element with multimeter for continuity. Checked good. Internet how to, suggested thermal switch. checked switch with multermeter, checked bad. Ordered switch kit. replaced same. smooth repair. wife was upset because I fixed the old dryer instead of replacing it. I kept a consideral dollar amount in my pocket by repairing the dryer. Purched the pair in 1989.
After reading a few online suggestions I didn't take any chances with the repair. I had looked at the heating element enclousure and found the thermostats and thermal fuse. I found the parts I needed on PartSelect and ordered all three. The thermostats were easy to replace as they were located in plain view. Removing the old heating element was a little more difficult but once I found the screw at the top of the enclouse (there is a hole in the back of the dryer cabinet above the back cover) I was able to use a nut drive (with extension) to remove the hex head screw and the enclosure came right out. One screw holds the heating element in the enclosure. The old heating element looked like it was rusted through - I'm sure the high heat over the 18 years we've had the dryer caused the oxidation. The whole thing took right at 30 minutes and was basically just removing the old parts and plugging the wires back on to the new parts and replacing the scrwes.
It's always on the weekend, usually on sunday...My wife came into the room and said her clothes dryer was broken. The clothes are wet and not hot. I figured the heating element was burnt out...the machine is 11 years old and she uses it 4 to 5 times a week. I pulled the electrical plug and opened the front panel. I disconnected one lead to the heating element and checked for continuity with my Ohm meter. No continuity. Burnt out heating element. I disconnected the other wire and two screws to remove the heating element assembly. I could see the broken coil. I went on line to PartSelect.com and found our dryer in about 2 minutes. There was an Illistrated Parts Breakdown with a picture of our heating element along with the thermal cut-off switch and the thermostat and we decided to replace both since the price was right and we had the dryer appart. I ordered our parts on-line at 5 pm on Sunday and recieved the package, with standard shipping, Tuesday around 3 pm. Unbelievably fast. The package was not damaged and we recieved exactly what we ordered. Reassembly was 15 minutes...the right parts fit perfectly. My wife claims that the dryer works better now than it ever did. I'm not kidding. She's happy and I get to watch football and drink beer while she's doing laundry. I'm the hero but I'll admit, PartSelect made my job EASY! Thankx you guys.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.