333298-1-S-Whirlpool-238460            -Door Hinge - Left Side
333298-1-S-Whirlpool-238460            -Door Hinge - Left Side 333298-2-S-Whirlpool-238460            -Door Hinge - Left Side

Door Hinge - Left Side

PartSelect Number PS333298

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $5.35
  • You Save

    $.89
  • Your Price

    $4.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

HINGE

Part Number 333295

$4.46
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.0 / 5.0, 1 reviews What's this?
1-1 of 1
 

44 of 230 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerJohn from Plymouth MI

Ravages of time and 7 children.

Dryer was making a thump-thump sound as it turned and door had to be held shut with a prop rod or it would pop open all the time.

First I reviewed the exploded diagrams of my model on the PartSelect website. I kept referring to it as I went.

Two screws held the console down, I removed those and disconnected all the wiring to the console and set the console aside. I popped the top from the front after removing the ground wire that the console had hidden. Oops ... forgot the screws holding the filter enclosure to the top panel. I removed them, then the top came off of the rear hinge-like things.

I turned the drum by hand and confirmed that it was "thump-thumping". There were two internal screws that held the front panel and door to the side panels, I removed them and then the front panel/door assembly buckled away from the drum slightly. I had to disconnect the wires from the door switch and remove the wire retainer from the front panel.

The front panel/door lifted slightly and came off of retainers to the side panels near the floor. The drum was now suspended on the two rollers, belt tensioner pulley, and motor pulley. I removed the belt from the tensioner and motor and removed the drum.

I could see that one of my drum support wheels had a chunk melted or gashed out of it. Every time the divoted portion contacted the drum, it made a thump. I also noticed all the stuff that the kids had dumped in the dryer by lifting the front of the top panel, thinking it was a good hiding spot. The stuff included crayons, beads, assorted spare change, and a package of peanuts that had broken open.

I took this opportunity to vacuum out the interior of the dryer. Wow.

One of drum support roller axles has a front support. Both are bolted into the interior panel with a washer and nut. I wanted to remove both axles to replace the support wheels, so I crawled behind my dryer (by climbing over my washing machine).

I had to remove the flexible vent and the rear panel cover to access the roller axle nuts. But one of the axle nuts was covered by the dryer filter enclosure, so I had to take it loose. Boy am I glad that I did. It was chock full of caked together lint and more crud that the kids had shoved down the filter hole when the filter wasn't in place. I cleaned it and removed the axle nuts.

I had to remove and replace these funky little plastic triangles that acted as retainers for the drum support wheels. It was difficult and I eventually had to use pliers to help. I swapped drum support wheels, installed the new plastic triangles and reinstalled the axles, filter enclosure, back panel, and flexible duct (this involved all sorts of tools and several trips back and forth over my washing machine).

I installed the drum, making sure the felt was not bent the wrong way and that the drum support wheels were in the drum groove. To rethread the drum belt I had to lay on the ground and hold the drum in position with my foot while guiding the belt with two hands. Once the belt was properly threaded, the drum would dangle in position, but I used the prop rod to support if firmly while I worked on the front panel.

The front panel was in sorry shape. I replaced both hinges, cleaned the area between the door and the front panel that cannot be reached easily, and replaced the door support wires and guides, reattaching their springs. I also replaced the door retention hardware. (Note: pliers recommended by my poor cut fingers).

I installed the front panel to the side panels by sliding it onto the two lower supports while holding the drum in position. I reconnected the door switch and wire retainers. I screwed the upper screws from the side panels to the front panel.

I popped the top panel back in place, routing the wiring through and reconnecting the grounds. I rewired the console and slid it back into position. I screwed down the console and reattached the filter enclosure to the top panel.

I plugged it in, turned it o

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-1 of 1