330540-1-S-Whirlpool-2203266           -Light Lens
330540-1-S-Whirlpool-2203266           -Light Lens 330540-2-S-Whirlpool-2203266           -Light Lens

Light Lens

PartSelect Number PS330540

Manufacturer Part Number 2203266
Manufactured by Whirlpool

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $29.46
  • You Save

    $4.91
  • Your Price

    $24.55
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 5 reviews What's this?
1-5 of 5
 

5 of 6 people found this instruction helpful

Parts Used

  • Light Lens

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJennifer from Islandia NY

The piece that covered the light at the back of the fridge burnt a hole in the cover.

First I removed the cover...and then I slid the new piece in. It looks great and so easy a caveman could do it...lol

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerFrederick from HoHoKus NJ

Fridge door would not close properly and therefore was letting cold air out and wasting energy

Removed lower door hinge and allowed door to drop down and off of upper hinge. Replaced cams on both hinge and on bottom of door. Reinstalled door. Also installed light cover that had broken years ago, but this is a pop-in item and no-brainer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerGregory from Virginia Beach VA

Noisy belt/slipping intermittantly

Unplug Dryer. Remove lower and upper front panels [remove wires from upper right door switch]. Lift up on belt idle pulley and take belt off pulley/motor.Remove Front Bulkhead and dryer lint/vent ducting. Note position on drum and remove belt. Unbolt top panel front 2 screws to allow room to remove drum.Remove drum. Take lock rings off Drum support rollers and remove old rollers. Clean roller shafts and apply hi-temp grease [I used ultra hi temp brake grease-ceramic based-small packet can be purchase fm auto parts store]. Re-install new support rollers and lock rings. Re-install drum and slide belt back into position. Remove and replace felt pads and glides into inside of Front Bulkhead. Reinstall Front Bulkhead and top panel [connect door switch wires].Install belt around idle tension pulley. Re-install lower panel.All parts fit perfectly and delivered quickly.Belt had just been replaced previously.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Light Lens

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGlenn from Cross River NY

Light lense tabs broken off . Lense was too close to light bulb which melted lense.

Removed old lense and spapped new one in place. This will break again because lense is to short and the tabs holding it into the sides of the refrigerator are barely long enough.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerNicholas from Pleasanton CA

Replaced broken/worn parts

Simple replacement

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5