328747-1-S-Whirlpool-2188542           -Icemaker and Water Dispenser Dual Inlet Valve
328747-1-S-Whirlpool-2188542           -Icemaker and Water Dispenser Dual Inlet Valve 328747-2-S-Whirlpool-2188542           -Icemaker and Water Dispenser Dual Inlet Valve 328747-3-S-Whirlpool-2188542           -Icemaker and Water Dispenser Dual Inlet Valve http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/TEKUJEJC.gif

Icemaker and Water Dispenser Dual Inlet Valve

PartSelect Number PS328747

May look different but will still function the same as the original and it is an authorized manufacture replacement.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Ice maker not making ice.
  • Not dispensing water.
  • Ice maker won’t dispense ice.
  • Compare At

    $72.16
  • You Save

    $12.03
  • Your Price

    $60.13
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 67 reviews What's this?
1-5 of 67
 

216 of 233 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench (Adjustable)

CustomerJoseph from Jacksonville, FL

Ice maker fill tube freezes up

After a bit of troubleshooting it became obvious that the fill tube was freezing shut because the dispenser valve was not fully closing between fills. It was allowing small drops of water to creep into the fill tube where they would freeze as they entered the freezer compartment eventually plugging the tube shut. The fix was to replace the valve which was conveniently located on the back of the refrigerator in the lower right corner (where you attached the water inlet line from the house). After unplugging the refrigerator and shutting off the water outlet valve (in the wall), a small crescent wrench easily removed the inlet water line from the valve on the refrigerator. I then had to remove about five or six screws which held the black (cardboard like) flap which covered the valve. This cardboard is part of the overall cover that encompasses the entire back of the refrigerator. Two sheet metal screws (which held the valve to the refigerator frame) were then removed and the valve was easily pulled from the frame about three inches. At that point four electical (plug like) connections (they're grouped in twos) were easily pulled off, and the two water lines which feed the ice maker and the drinking water dispenser were easily removed using a pair of pliers (and fingers). To install the new unit, the aforementioned process was reversed and the unit has worked (and fixed the problem) perfectly! The only problem I encountered was that I had a small leak where you attach the water line from the wall to the new valve. This was fixed with some plumbers tape.

Help other customers find the most helpful instructions.

Were these instructions helpful?

65 of 81 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench (Adjustable)

Customervince from antioch, CA

No water from dispenser but was getting water to ice maker

I unpluged the refigerator and turned off the water supply valve to the refigerator. I then disconnected the main water line to the refigerator and the 2 lines underneath the unit. I then unscrewed (2 screws) the unit from the refigerator. Then disconnected the 2 small plugs to the unit (sylonoid valves). I reinstalled the new unit in reverse. Turned the water back on checking for leaks then plugged the refigerator back in and tested the water despensor.

It was that easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

49 of 56 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerDean from Sheboygan, WI

Ice maker over flowing in freezer

After finding my ice maker and ice bin over flowing with frozen water. I unthawed my freezer wiped it down and started over again, only to find the water flowing into the ice maker didn't stop flowing. I determined the problem to be with the DIspenser valve. To replace this vave was a 15 min. job. Shut off the water to the refrigerator. Unplug the refrigerator. Remover the cardboard cover on the back of the frig. In the lower right hand corner of the frig is the dispenser valve. Remover the 2 screws holding it to the frig frame. Then it is just a matter of unplugging the 2 wires and unscrewing the 3 water lines from the old valve and placeing them in the same places in the new valve. Replace the cardboard,plug in the frig and turn the water back on. It did take a few ice making cycles for the ice maker arm to stop sticking in the up position. Very easy job!

Help other customers find the most helpful instructions.

Were these instructions helpful?

48 of 74 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerTrent from Tacoma, WA

Water dispenser started leaking

i wasn't sure it was the inlet valve unit because the leak was at the water dispenser in the freezer door. after some research it looked like the water inlet valve located in the back lower part of the refrigerator was the problem. to replace, take off the cardboard cover, about 6 screws, you have access to the water inlet valve, disconnect the hoses (i think it goes without saying that you should have turned off the water to the frig) replace the inlet valve, connect hoses, turn water back on and you'll be back in business. very easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31 of 36 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench (Adjustable)

CustomerStanley from Sacramento, CA

Water dispense stopped working

1. Removed cover panel which was attached with seven screws.
2. Turned off the water supply valve to the refrigerator.
3. Unplugged the power to the refrigeration.
4. Unfastened the inlet valve which was fastened with two screws.
5. Unfastened three water hoses from the inlet valve with an adjustable wrench.
6. Unplugged two sets of electrical wires from the inlet valve.
7. Reverse the steps to install new inlet valve.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 67