328747-1-M-Whirlpool-2188542-Icemaker-and-Water-Dispenser-Dual-Inlet-Valve.jpg
328747-1-S-Whirlpool-2188542-Icemaker-and-Water-Dispenser-Dual-Inlet-Valve.jpg 328747-2-S-Whirlpool-2188542-Icemaker-and-Water-Dispenser-Dual-Inlet-Valve.jpg 328747-3-S-Whirlpool-2188542-Icemaker-and-Water-Dispenser-Dual-Inlet-Valve.jpg

Icemaker and Water Dispenser Dual Inlet Valve

PartSelect Number PS328747

This valve may be a replacement from the original depending upon your model number. It will function the same as the original.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Ice maker will not make ice.
  • Water dispenser will not dispense water.
  • Ice maker won’t dispense ice.
  • Compare At

    $65.69
  • You Save

    $10.95
  • Your Price

    $54.74
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 67 reviews What's this?
61-67 of 67
 

0 of 2 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench set

CustomerWilliam from Oceanside CA

Water dispenser stopped working; ice maker still worked

Shut off water supply to refrigerator at wall. Disconnected water supply line to fridge. Removed three self tapping screws holding cardboard cover to dual inlet valve. Folded cardboard out of way, but did not damage it. Removed two screws holding inlet valve in place. Pulled inlet valve out from refrigerator. Lots of dust. Vacuumed out some of it. Removed both electrical connectors (one for water to dispenser, the other for water to ice maker). It is impossible to mix these up since the connectors are sized differently (thank God). Unscrewed both water lines from the defective inlet valve (easily done since they were hand tight) and screwed them on the new valve (finger tight only). Reconnected both electrical lines. Bolted new inlet valve in place with two screws. Attached water line from wall to valve and turned on water supply. Checked for leaks. Operated now working water dispenser and flushed gallons of water to clear the lines and tank behind crisper. Checked again for leaks at inlet valve. Found none. Replace cardboard cover and screwed back in place with three screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMike from Walnut Grove MS

Ice maker would not operate and water dispenser operated properly

My ice maker would not operate at all. I viewed the tutorial for the ice maker and followed all steps in correct order. The only deviation I took was to disconnect the original wiring loop from the old ice maker instead of the refrigerator. I took this route because I felt I had to put too much pressure on the loop at the refrigerator end. Anyone deciding on this deviation just has to inspect the in-line fuze on the old loop. If the original problem was the fuze, the fuze housing would be melted to some degree. It should be noted that the ice maker has to be removed from the freezer wall in order to properly inspect the fuze. Otherwise the entire operation involved the use of a 1/4 inch nut driver to loosen two top screws and remove one screw on the bottom.
After installing the new ice maker I found I had no water from the dual water valve located on the bottom rear of the appliance. I installed a new water valve by removing the two 1/4 inch mounting screws and while holding the old and new valves side-by-side moved the three water lines and two wiring harnesses from the old to the new and remounted the assembly. After about three hours the freezer was cold enough to start making ice. We ran about two gallons of water through the water dispenser and discarded the first three trays from the ice maker to purge and clean the system.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Wrench(Adjustable)

CustomerRosario from Cape Coral FL

Ice maker not making ice

Shut off water supply,to refrigerator. Then removed cardboard backing covering inlet value. Shut off electric,
removed water supply lines and cleaned out with air. Disconnected value and replaced with new one , all fittings fit perfect you can not make a mistake. Plugged in refrigeratoe and turned on water supply. In about one hour had ice again. The repair took about one hour. Very happy with results. Thank you Part Select.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerChristopher from Scarbro WV

Ice tray overfilling

Ice tray in the ice maker was overfilling with water, and running out all inside the freezer.
Going by similar problems described that other people had, it seemed it was a bad dual inlet valve.
I replace the valve, which was very simple to do using nothing more than a nut drever, and a cresent wrench. But unfortunatly it did not fix the problem.
Ice tray still overfills with water.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerDavid from Fairfax Station VA

The icemaker didnt work

I shutoff the water, removed the back cover, disconnected the old piece and replaced the new. Checked for leaks and replaced the cover. Easy job, took maybe 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerDonald from Pacifica CA

No water dispensing

My water dispenser stopped working after using for sometime with a buzzing noise before water would dispense. After looking at Partselect .com parts diagram I found the water inlet valve was two valve assembly. One part of the valve is for the ice maker that worked fine.What I was hearing was the dispenser valve side solnoid trying to operate. After vacuum cleaning the coils and fan area and turning off the water to Frig. I replaced the valve, turned on the water,checked for leaks, It worked fine.. the part was delivered almost over night. Thank You PARSELECT.COM.....Don

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • Icemaker and Water Dispenser Dual Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerBarbara K. from Monroe MI

Not making all of the ice cubes.

The repair went great. It took less than 15mins. once the part arrived. Just to let others know that ordering the part was so easy. And were we surprised when the part came that next day. We'll let all our friends and everyone we know where to go the next time they need any part should they need to do so. Thank You so much.AAAAA*****. Joe& Barbara

Help other customers find the most helpful instructions.

Were these instructions helpful?

61-67 of 67