| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerGary from Citrus Heights CA
Getting no water from door
The bracket that held the micro switch had broken, I had to replace the cover brace assembly. The job went smooth.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
CustomerRICHARD from SAPULPA OK
Broken micro switch holder
SIMPLY, REMOVED COVERED TOOK OFF PARTS, AND REPLACE ON NEW PART, REHOOKED REPLACED COVER. IT IS A BIT TEDIOUS REMOVING THE COVER ON THE ICE DISPINSER BUT IT IS SLOTTED AT TOP, SILL POP OFF EASILY BUT BE CAREFUL CAN BREAK IF YOU FORCE IT.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerElizabeth from Dallas TX
Water dispenser wasn't working
called in a repair company and they wanted to charge me $350.00 to repair it so I went on line and found some people had replaced the control bracket, so thought what can I loose? Ordered the part and replaced it within about 30 mins. Now it works perfectly!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customermark from Blaine MN
Water did not work
removed front of control to find the control board broken. The switch was working ,but the broken part of the board would not allow the switch to work.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerclinton from Lees Summit MO
Water dispenser not working
I searched the internet and found "partselect.com" put in my model number and they said the part that usually fails is the bracket that holds the micro switch, I proceeded to take the cover off (hardest part) it needed alot of downward pressure and snaps off. Sure enough the micro switch was loose, I ordered the part for $ 18 with shipping included, it arrived in 2 days and took about 10 minutes or less to transfer all the stuff from the old bracket to the new bracket. THANKS ! !
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJane from Hartselle AL
Ice working; no water
follow the above directions. The front panel is very tight. You have to pull it use a fair amount of force to get it off. Same with pulling the wires apart. Part number 8 had fallen off. It is shorter than the diagram shows.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customercarlos from woodhaven NY
Not ice come out
removing the cover and replaced panel that hold the switch, and problem fixed
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAloysius from New Braunfels TX
Broken water dispenser.
I originally thought something was wrong with the circuit board. After taking a closer look I realized the plastic bracket holding the control in place had snapped off. A few screws and about 10 minutes is all it took to replace.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerRobert from Aurora IL
Broken frame to supopport water / ice dispenser controls
REFRIG REPAIR WENT WELL BUT COULD HAVE USED SKETCH OF PARTS TO REMOVE AND REPLACE
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJonathan from Roseville MN
Ice would not dispense
Removed a couple of screws that hold the cover to the door. Took the cover off and unclipped a few wire harnesses holding the cover in place. Removed two more screws and took the control bracket out. Took everything off of the old control bracket and put it on the new control bracket. Then reassembled.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDuane from Lexington KY
Broken housing bracekets that held water cut off switch
We had an appliance repairman quote of $194.00 to replace the part in the next 5-7 days. However, it seemed exhorbitant so I paid him the $24.95 for the service call. The part and shipping was $18 and some change and arrived the nest afternoon FedEx. So for about 15 minutes of work I saved $150. The repair is every simple, just pop off the face plate and remove/replace switches, wiring harnesses, etc.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGuirlene R from Buford GA
Water dispenser water dispenser stopped working.
first I took out the old Control Bracket with my flat head screw driver. After taking the wires out of their sockets, I simply put the new Control bracket in and then put the wires back in . Delivery took 3 days,.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:More than 2 hours
ToolsScrew drivers
Customernicholas from flamington NJ
Ice dispenser not working
it took me longer to correct the problem because i started to troubleshoot inside the freezer.checked the door switch ,solenoid and gear motor.they all were good ,than i went to control panel on the front door. removed front cover and found broken pins on the control bracket. ordered a new control bracket , installed a new bracket and the ice dispenser is working again. to install a new bracket it took me 15 minutes
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
Customerwesley from jonancy KY
The ice maker would not despince ice
with a nail catch under the face plate at bottem and pop off then uplug switich wire then unsnap old bracket and snap new one inplace simple there are no screws
|
0 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerNorm from Randolph NY
Broken bracket for water dispenser
I popped the front cover off of the LH door by lightly prying with a flathead screwdriver. The bracket was under the cover and it came out by popping the retaining tabs to the side. I removed the wires and switches from the old bracket and moved them to the new bracket and reinstalled the new bracket by pushing into place. I then snapped the cover back into place.
The bin for the door was as easy and just sliding into place.
|