323447-1-S-Whirlpool-2155013           -Bottom Kickplate Clip
323447-1-S-Whirlpool-2155013           -Bottom Kickplate Clip 323447-2-S-Whirlpool-2155013           -Bottom Kickplate Clip 323447-3-S-Whirlpool-2155013           -Bottom Kickplate Clip

Bottom Kickplate Clip

PartSelect Number PS323447

This clip is sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $7.69
  • You Save

    $1.28
  • Your Price

    $6.41
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 3 reviews What's this?
1-3 of 3
 

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRandall from Perry IA

Unit stopped making ice

First, I loosened the two top screws and removed
the bottom screw. Then lifted the unit up and out.
Next, I unplugged the wire plug and removed the
ice maker unit from frig. The replacement ice maker was identical to the original, wire loom and all. So all I had to do is plug in the wire plug, slide the top down on the loosened screws and tighten them. Next, installed the bottom screw, turned on the water,flipped the wire down and waited for ice. We had ice being made by the next morning and in about 3 days had a full bin.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJoseph from University Place WA

Replaced broken/missing parts

poped in, replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Bottom Kickplate Clip

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set, Wrench(Adjustable)

CustomerGregory from Virginia Beach VA

Dryer made loud intermittant humming sound after 20-30 minutes of use

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3