| |
4 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerTobi from Kansas City MO
The drawer slide was broken and wouldn't hold the drawer up anymore.
I removed the drawer unscrewed the screws that held in the slider rail. I put the new rail in place of the old one and screwed it in. I replaced the drawer. It took a little longer because I cleaned out the fridge while I was in there. I actually had more parts than I needed, and will be returning a couple of things. It was really easy.
|
4 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBoris from Miami FL
Broken rails
Took out drawers, unscrewed broken rails, screwed on new railings with new screws, replaced old drawer with new one. Less than 15 min.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerMarilyn from Corinth TX
The slide rails and kickplate just broken
I replaced all the parts and it was easy. I still need a door drawer that I will get later.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerArchie from Arlington VA
The veggie drawer fell down from the slide on one side
So I looked at it, and saw the slide had actually broken. Immediately copied the Model Number and put THAT number into the Google Box. Up popped the Part Select site -- along with others. There was a perfectly understandable schematic (interactive.) I figured out what I needed, and ordered the parts. They arrived, and the fix was simple!!!
No $85 service call
No "We'll be there between 8 and 5"
Simple.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerWayne from Riverside CA
Storage drawers slides were broken
First I removed all the broken pieces with a screwdriver. I then installed the upper drawer slides and then the lower. Put the glass in was easy. All you had to do was put it in the slots on top of the drawers. The filter of course was unscrew the old one and screw on the new one. All in all is was an easy experience. Too bad it took us over a year to order the parts.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCindy from Manhattan KS
Broken slide rails
Removed broken slide rails (2 screws per rail) and replaced new rail. Easy as drinking my morning coffee.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid from Arlington VA
The left side drawer slide rail broke
When the drawer slide rail broke, I thought that I would have to go to Home Depot, find out that they didn't have the part, and have to go through a lot of hassle to get it fixed. I went online and through a Goggle search found Parts Select. It was SO EASY!!!! I typed in my refrigerator's model number and while they didn't have the exact Hotpoint model, they did have model's that were a close match. I picked the model that was closets to mine. The parts page was so easy to figure out. Through the diagram I found my part, you can even click on it and get a larger picture so that you can compare the picture with your actual part. I order what I needed and the parts came right on time. I actually did the repair and not my husband. I was done and everything cleaned up by the time he came down from taking a shower. In fact, the whole repair job and putting the drawer back in took about 5 minutes. I have told all my friends and am recommending Parts Select to them for their repair needs. The next time something breaks, I will go to Parts Select first!!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsScrew drivers
CustomerGary from Lake Worth FL
2 verticle and 4 horizontal drawer brackets a broke
Removed(unscrewed) broken parts and replaced with new parts.
I suggest parts be marked left or right
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerJames W. from Columbus MS
The crisper bin slides had broken
Removed the bins, and the broken rails. The rails for the upper bin is made for three screws in each rail, and they were installed with only two screws, ehe front and back screws were installed and the middle screw holes had never been drilled for screws. Install the new rails with the front and back screws, then "CAREFULLY" use an electric drill to drill the middle screw holes, and install the middle screws. These screws help relieve the pressure on the front screws when the drawer is pulled out.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from Crofton MD
Old parts broken and or cracked so drawers didn't open easily and shelves were uneven
First I removed the drawers and shelves. Then I removed the left and right trim pans (1 screw ea). Next I removed the two screws (8 total) for each of the left and right drawer slide rails and rail assemblies. Then I spent way too much time cleaning the bottom half of my refrigerator, the shelves and drawers! After finishing the cleaning, I installed the lower left and ride slide rails (2 screws ea). Then I installed the upper left and right slide rails (2 screws ea). I then installed the left and right trim pans (1 screw ea). After that I set the bottom shelf and drawer in and then did the upper shelf and drawer.
The packaging was OEM, clearly marked too. The hardest part of the job was cleaning my refrigerator!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLonnie from Moncure NC
Slide rail broke with too much weight in the crisper drawer
I removed the top crisper drawer and the glass shelf above it. I then removed 2 screws and placed the new bracket in place and installed the 2 screws. About 5 minutes to complete.
|
0 of 7 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerNNora from Miami FL
Bottom fridge drawers/shelves fell when brackets broke...
my 15 year old son did the install in 30 minutes
back in functional order and looks like
satisfied customer!
|