| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCharles from Hattiesburg MS
Drawer had been falling off the rails for several years and finally decided to look for parts.
The left and right rails came in quickly by UPS and after opening the box, I compared to old parts and found they were an exact match.
I then proceded to remove the two defective rails. It was quite simple. There were 3 phillister screws holding on each rail. I simply removed the old rail one at a time and replaced with the new one in reverse order of removal.
After replacing both rails, I replaced drawers and now no more drawer dropping. I only which I had discovered Parts Select.com 2 years ago. It was simple to order, amazingly could still get parts, and clear diagrams and easy to identify part numbers. I will refer to this company in future for all of my parts needs if available.
Thanks,
Charles from Hattiesburg Mississippi.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from Crofton MD
Old parts broken and or cracked so drawers didn't open easily and shelves were uneven
First I removed the drawers and shelves. Then I removed the left and right trim pans (1 screw ea). Next I removed the two screws (8 total) for each of the left and right drawer slide rails and rail assemblies. Then I spent way too much time cleaning the bottom half of my refrigerator, the shelves and drawers! After finishing the cleaning, I installed the lower left and ride slide rails (2 screws ea). Then I installed the upper left and right slide rails (2 screws ea). I then installed the left and right trim pans (1 screw ea). After that I set the bottom shelf and drawer in and then did the upper shelf and drawer.
The packaging was OEM, clearly marked too. The hardest part of the job was cleaning my refrigerator!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerangela from East Peoria IL
Slide rail was broken.
Removed the drawer from the fridge. Removed the 2 screws holding the cracked slide rail and removed the slide rail. Installed the new slide rail with the 2 existing screws. Re-installed the drawer. Super Simple.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerpatricia from baltimore MD
I had a hugh christmas party and had lots of heavy items on top of the refrigerator pull-out drawers causing one to actually collapse and break the sliders. I found the part I needed on your site, received it in just a couple of days and quickly repaired the large drawer slider. It works perfectly
Screwed the slider into the side of my refrigerator, added the drawer and glass top. All fixed as good as new.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKENNETH from MINOOKA IL
Drawer slide broke at screw fastener
2 screws removed and replaced w/ new bracket...part was delivered very promptly (2 days!) :)
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerrobert from fountain hills AZ
Bronken drawer slide
Removed the 2 screws, removed the old pieces of track and installed the new piece by reinstalling the 2 screws
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDarrell from Omro WI
Went great ! Everything fit & bam I was done.
Simply removed the broken part & replaced it with the new part in about 5 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKathye from Swansea SC
Drawer slide rail broke
Quickly found needed part at web site and received an answer to a question quickly. Part arrived quickly and as promised. Installed in minutes.
Thank you
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerWilma from San Diego CA
Drawer slides rail broke (two right sides)
Take everything out of refrigerator that sits on the drawer slides, remove screws that hold old drawer slides in place; put new drawer slide in place; then insert and tighten screws. Very quick and easy.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerSoumya from Mechanicsburg PA
Drawer slide rails broke
It was really easy. I removed my drawers out. (They were kidn of sitting on the base and the glass because the rail broke). All I had to do was unscrew the broken rail and screw in the new one. Good to go in 10 minutes!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerVaughn from Aurora CO
Broken drawer slides
This was a very easy repair. I simply removed the screws that held the drawer slide rails and trim pans, and replaced the broken parts. No sweat!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRichard from Southlake TX
Drawer slide broken; fell completely off.
The drawer and shelf malfunctioned from day one. After being shocked by the appliance store's denial of fault and the estimate to repair I went online and Googled the model number of my refrigerator. Lucky for me I found Parts Select. I ordered the part for a tiny fraction of the repair estimate and received the part in three days. The replacement was very simple -even for a middle aged real estate attorney. I removed the drawer and glass shelf; removed two phillips head screws; lined up the new part replaced the screws slid in the drawer and sat the glass shelf in place. Looks new, works like new. Thank goodness for PartsSelect.com
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRichard from Oswego IL
Broken shelf bracket
Received the part in a couple of days. Replaced drawer slide. Repair completed.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLonnie from Moncure NC
Slide rail broke with too much weight in the crisper drawer
I removed the top crisper drawer and the glass shelf above it. I then removed 2 screws and placed the new bracket in place and installed the 2 screws. About 5 minutes to complete.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerHenry from Georgetown KY
Broken slide rail at screw attachment point
I removed all items on the shelf that the rail supported. I removed the crisper top and crisper. I removed the 2 screws that held the broken rail and removed the broken rail. I set the new slide rail in place and tightened the 2 srews. Then I reinstalled the crisper and crisper shelf. This was a very simple, easy repair. The most difficult part of the process was identifying the correct replacement rail online.
|