| |
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Right Side
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomerAnthony from Manalapan NJ
Cracked slide rail
Removed screws . Drilled new holes since the current holes were too wide. Did same on left side. Lovered drawer by 1/4 inch. No problem.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCarie from Falls Church VA
The drawer slide rails wore out (imagine that after 1o years and 5 kids in and out of it everyday!) and we needed to replace them.
Took out the drawer. Removed broken slide rails with screwdriver (two screws each), installed new slide rails with screwdriver, replaced drawer. Voila!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBrian from Overton NE
Slide rail broke
Remove and replaced. It is companies like PartSelect that make the internet worthwhile. The part arrived in 3 days and fit perfectly.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMike from memphis TN
Broken drawer slides
remove two screws and replace with new drawer slides a very simple task,eight screws later and all four slides were repaced
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLane from Pittsville WI
Broken slide rails - drawers kept falling out
Removed the two screws that held each rail in place, cleaned fridge well underneath them, put new rails on with the two screws each. Simple repair, perfect fit parts, beautiful results - looks like new.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMona from Havelock NC
Drawer slides were broken
First I removed the two screws that hold the drawer slide in place. I cleaned the area where the old slide had been. I then put the new slide in place and put in the two screws I had from the old slide. I did this for all three slides I received.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerThomas from TALLAHASSEE FL
Slide rails had broken.
The repair itself was easier than finding the parts. After looking on a number of websites, including GE's own website, I found the parts at PartSelect.com. The picture made it easy to ensure that these were the right parts. They came in the mail quickly, so I was very satisfied. I have kept my paperwork so I can return to PartSelect.com whenever my appliances need repairs that I can do myself. Thanks!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRae from Gambrills MD
The drawer track on my refrigerator broke, so we ordered the part and now the drawer is in place again.
Removed broken track by unscrewing it and screwed in new track
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGary from Lakeport CA
Broken slide rails
Removed two screws on each slide rail and used the same two screws to install new rails. The job took only a few minutes. The best part was the promptness of the delivery. I ordered the parts at 12P on Thurs and had them on my porch at 10A on Fri. Thanks Gary
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerHenry from Montezuma GA
The drawer tracks were broken
Took the old broken slide out and put the new one in.Very easy.It is so nice to have it fixed.Thanks so much for the fast service.Have a Blessed day.Henry
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerScott from Salisbury MD
The slide rails had broken over the years through normal wear and tear. The drawers would not track properly or at all.
It was a simple matter to just unscrew the remaining pieces of the old slides and then screw in the new parts. Because I had waited until several needed replacing, it was important to make sure I had the right part for the right side and the right drawer.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customertodd from morro bay CA
Broken cooler shelves in my refridgerator.
My Hotpoint fridge did not have working cooler shelves due to years of service. I was able to remove the slide drawer rails, install the new rails, and replace the drawers. It works great! PS: Clean the fridge first to make the job easier and to make a wonderful presentation when you show your hard work to your wife!!!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerEVA from OSSINING NY
Broken rails
EASY REMOVAL WITH SCREWDRIVER;TRO UBLESHOT CAUSAL EFFECT OF [ METAL]
SCREW AGAINST {PLASTIC] RAIL WHICH CAUSED BREAK. MY SOLUTION;TOOK BIKE INNER-TUBE, SISSOR-CUT AND FASHIONED SMALL 'GASKET' WASHERS TO SOFTEN CONTACT POINTS ON BOTH INNER & OUTER SIDES OF RAILS. TOUCHED UP RUSTY AREA AROUND SCREW-HOLES WITHIN FRIDGE WITH SANDPAPER & RUST-INHIBITING SPRAY PAINT
GOOD TO GO! THANKS FOR THIS OPPORTUNITY
TO SHARE A PREVENTATIVE SOLUTION / UPGRADE!
|