305238-1-M-GE-WR71X10197-Ice-Bucket-Support-Right-Side.jpg
305238-1-S-GE-WR71X10197-Ice-Bucket-Support-Right-Side.jpg 305238-2-S-GE-WR71X10197-Ice-Bucket-Support-Right-Side.jpg

Ice Bucket Support - Right Side

PartSelect Number PS305238

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $6.65
  • You Save

    $1.11
  • Your Price

    $5.54
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Ice Bucket Support - Left Side

Part Number 305237

$5.13
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

7 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRoger from Norman OK

Ice bucket shelf broke at screw hole also at back . Metal attachment at back broke free from fan cover.

GE in my opinion made a poor design the ice shelf bracket attached to the metal fan cover after metal tab was bent down that is also where it broke it was riveted to this but the metal broke free
So i purchased a piece of aluminium flat strap cut this about 1" long then riveted this to the shelf bracket and pushed this through the metal fan cover and let rest there and put screw in at other end. Also purchased alum angle also to remake ice shelf when complete then i will use it as ice bucket shelf instead of plastic one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerM R from Las Vegas NV

Ice maker bump and grind

The ice bucket supports had split, and broken away from the refrigerator wall causing the ice dispenser bucket to sag, and bump and grind. The b&g wore away the ice screw support at the rear of the bucket, causing intermittent ice dispensing. The ice bucket was removed to allow access to the ice bucket supports. The supports were attached to the refrigerator by two screws. One along the front side, the other at the rear attached to a protruding tang. One of these broken off, the other was stuck, and had to be forced off its mount. The rear mount was expanded by drilling a slightly larger hole to accommodate a nut and bolt assembly. The new support units were re-attached to the refrigerator front and back using screws and the nut and bolt in the appropriate places. The ice bucket installation was a tad more difficult. The hardware from the original bucket was removed and installed on the replacement bucket. This proved to be a bit tricky remembering the exact location of the parts, and coordinating the screw mechanism with the driver mechanism. The ice fill starter switch is a bit unusual in that it has to go into a slot that is not visible when inserting the ice dispenser bucket into the ice maker compartment. You have to finagle the bucket into place and get all the parts in the correct slots. It was a piece of cake for the average husband.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Ice Bucket Support - Right Side

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRose from Tyler TX

One of the ice bucket shelves was broken.

Simply removed the screws and replace the shelve. 5 minutes tops. Saved the right shelve for later.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRobert from Oro Valley AZ

Could not install ice bucket shelfs becase back attachment is riveted not screwed.

Light shield easily installed with one screw. Can not istall the 2 ice bucket trays because the back attachment on each is a rivet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4