Quick Question!

Have you ever purchased from PartSelect.com before?

304731-3-S-GE-WR60X187          -Condenser Fan Motor - 115V
304731-3-S-GE-WR60X187          -Condenser Fan Motor - 115V 304731-1-S-GE-WR60X187          -Condenser Fan Motor - 115V 304731-2-S-GE-WR60X187          -Condenser Fan Motor - 115V http://www.partselect.com/Schematics/GE/00006679i01.gif

Condenser Fan Motor - 115V

PartSelect Number PS304731

This part comes with 3 round pin connection terminals. This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Fridge too warm.
  • Freezer section too warm.

Compare At

$213.52

You Save

$35.59

Your Price

$177.93
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 6 reviews What's this?
1-6 of 6
 

23 of 28 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kimberly from Grandy, NC

Panel hot to touch between freezer & refrigerator. Motor hot, fan not rotating.

Unplugged refrigerator, removed three screws to take out part, disconnected the wires and removed bad unit. Removed fan blade from old unit and attached to the new unit. Attached wires, placed the new motor back in. Plugged it back in, within 20 minutes panel between freezer and refrigerator was cool to touch.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 15 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: CHRIS from LAGUNA NIGUEL, CA

Compressor overheating - fridge not cooling

Condensor Fan not turning. I thought it would be an easy fix. I thought I could pull off the shroud and fan assy - no joy. Too many copper pipes and lots of tubing in the way. It took 90 minutes to remove and 30 minutes to install. The BIG hint here is to loosen the shoud, pull it back as far as you can and then remove the nut that holds the fan blade in place. THEN you can remove the motor. Get the new motor back into the shroud, get the blade back on and then tighten the shroud back up.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 11 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Wrench set
Customer: PERRY from VANDERBILT, MI

Noisey motor, bearings out, dying

Remove back cover, exposing fan motor. Turn off power, remove nut on fan blades. Remove fan carefully, do not bend. Unhook wiring harness. Remove three screws that hold the motor on the back frame. Remove old motor, install new. Carefully, reinstall fan blades, hook up wiring, and your ready for tryout. Also do some cleaning while your there. Clean old fan blades with hot soapy water or contact cleaner. Everything runs better clean!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 10 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: JEFF from HAMPTON, GA

Fridge quit coolingg / freezing

remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - replaced cover - was hero with wife ... :-)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 13 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: John from Divide, CO

Fan had quit; needed replacement.

The fan was the correct part. It arrived one day after my well trained son-in-law had left for Texas. I had to install the motor myself. He had trained me well; it was not hard. the most difficult was getting the two tabs on the fan housing to fit back into the frame of the refrigerator where they belonged. Thanks. the part & delivery were overpriced, but I needed seed and convenience. Thanks for getting it right the first time.
John Moragues

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 13 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor - 115V
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: donald from opelousas, LA

Noise from condenser fan

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6