BBB A-Plus

Single Outlet Valve Kit

PartSelect Number PS304375

This single outlet valve has 1/4 inch compression fittings, and is intended for use with refrigerators that have ice makers that make crescent shaped ice cubes. NOTE: As per the manufacturer this valve has new quick connection. You must cut retaining nut off of the current plastic water line and gently push it into new valve. To remove, depress ring that the tube slides into.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker will not make ice
  • Leaking water
In Stock

  • Compare At

    $25.72

  • You Save

    $4.29

  • Your Price

    $21.43
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 3 NEXT > 31-36 of 36

 

1 of 2 people found this instruction helpful

Parts Used

    • Single Outlet Valve Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerMargaret from Virginia Beach VA

Ice maker would only make very small and very few ice cubes.

After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed another screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

    • Single Outlet Valve Kit

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerPaulette from Crandall GA

Had never installed one before and was not sure which was top or bottom. The piece was made different than the original

Unhooked power to valve
Removed old valve by taking out 2 screws.
Used adjustable wrench to remove water lines. Then reversed and hooked everything back up

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

    • Single Outlet Valve Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsWrench set

CustomerFred from Crawfordsville IN

No water to icemaker

Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

    • Single Outlet Valve Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

Customerlarrie from punta gorda FL

Ice maker just stopped

part arrived on schedule,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

    • Single Outlet Valve Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerolin from forest city NC

Ice maker not working

First i shut the water valve off going to the fridge, I then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then i took the water line loose to the element, reverse the prosses and put all back on new element and installed,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerJAMES A from Orlando FL

Ice maker quit

i replace the IM3 with a upgrade to the IM6 ice maker. a simple swap and easy to install. with very good instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 3 NEXT > 31-36 of 36