Quick Question!

Have you ever purchased from PartSelect.com before?

304375-1-S-GE-WR57X10033        -Single Outlet Valve Kit
304375-1-S-GE-WR57X10033        -Single Outlet Valve Kit 304375-2-S-GE-WR57X10033        -Single Outlet Valve Kit 304375-3-S-GE-WR57X10033        -Single Outlet Valve Kit http://www.partselect.com/Schematics/GE/00009345i01.gif

Single Outlet Valve Kit

PartSelect Number PS304375

This single outlet valve has 1/4 inch compression fittings, and is intended for use with refrigerators that have ice makers that make crescent shaped ice cubes. NOTE: As per the manufacturer this valve has new quick connection. You must cut retaining nut off of the current plastic water line and gently push it into new valve. To remove, depress ring that the tube slides into.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Leaking.
  • Ice maker won’t dispense ice.
  • Not dispensing water.
  • Compare At

    $27.68
  • You Save

    $4.61
  • Your Price

    $23.07
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 37 reviews What's this?
31-37 of 37
 

2 of 5 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench (Adjustable)
Customer: TERESA from COALMONT, TN

Was not making ice or getting water

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Wrench set
Customer: Fred from Crawfordsville, IN

No water to icemaker

Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: larrie from punta gorda, FL

Ice maker just stopped

part arrived on schedule,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: olin from forest city, NC

Ice maker not working

First i shut the water valve off going to the fridge, I then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then i took the water line loose to the element, reverse the prosses and put all back on new element and installed,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Wrench set
Customer: FRANK M from EASTON, PA

Ice maker was not working

1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes

Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 7 people found this instruction helpful

Parts Used:
  • Single Outlet Valve Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Paulette from Crandall, GA

Had never installed one before and was not sure which was top or bottom. The piece was made different than the original

Unhooked power to valve
Removed old valve by taking out 2 screws.
Used adjustable wrench to remove water lines. Then reversed and hooked everything back up

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: JAMES A from Orlando, FL

Ice maker quit

i replace the IM3 with a upgrade to the IM6 ice maker. a simple swap and easy to install. with very good instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31-37 of 37