Water Valve and Bracket Assembly

PartSelect Number PS304368

This water valve assembly has been redesigned. It has a new quick connect style valve. To install: Cut original plastic nuts off tubing and gently push into valve until they stop. No other nuts or connectors needed.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Leaking water.
  • Water dispenser will not dispense water.
  • Ice maker will not make ice.
  • Compare At

    $110.95
  • You Save

    $18.49
  • Your Price

    $92.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 38 reviews What's this?
1-15 of 38
 

129 of 207 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench set

CustomerEric from Westerville OH

Water leaked out on floor from behind refrigerator.

First turned water source off and unplugged fridge. Then removed back panel, turned water supply back on and saw leak from valve. Turned water off again and ordered new valve. Paid for 3-5 day shipping, but it came next day! Removed single bolt holding bracket it place. Simple firm pull release of water lines feeding from valve. Unscrewed brass water supply nut with crescent wrench. Marked four electrical leads so I'd know where to replace them. Then repeated process in reverse to install new valve. Simply push water lines back into color coded valve outlets.Also replaced water filter and found that the GWF Filter is now the MWF fitler.

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 24 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerRobert from El Paso TX

Water dispenser in door failed to dispense water

Unplugged refrigerator from electrical outlet for safety and turned off water supply valve. Removed the four metal screws that hold the access cover on the rear of the refrigerator. Then removed single metal screw attaching water valve and bracket assembly. Unplugged wire harness from the water valve and assembly then pressed down on colored o-rings to detach the four plastic water lines from the water valves. Used open end wrench to disconnect main water supply line from the water valve.
Pressed down on colored O-rings to install the four plastic water lines to new water valve and bracket assembly. Wrapped plumbing tape on threads of inlet valve and and used open end wrench to attach main water supply line to new water valve and bracket assembly. Attached wiring harness to new water valve and bracket assembly. Mounted new assembly to refrigerator with single metal screw. Turned on water supply valve and checked for leaks. Plugged in refrigerator to electrical outlet and tested water dispenser. Replaced access cover on rear of refrigerator with four mounting screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerForrest from Surprise AZ

Water dispenser on door not working, but ice maker makes ice.

The hard part of this repair is moving the refrigerator away from the wall and cleaning all the dirt from the fan, condenser and area. Removing the old water valve takes about 5 minutes. Be sure to shut off water completly at the wall. I removed ea. water line one at a time from old valve & installed in new valve at the same time, to keep in order. Very easy to remove electrical connectors, one at a time and clip to new valve in proper order. I put some teflon tape on the main water connection & reconnected water line to valve assembly. Moved valve assembly back into position and installed with one screw. Installed the back cover with 5 screws, moved the refrigerator back and checked for water. The water dispenser works better than new and so does the icemaker. Thanks to partsselect.com for the help.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerRich from Keller TX

Water valve leak

Pull fridge out and turned water supply off. Removed four screws to take shield off back of fridge. Unscrewed assembly part from fridge. Turned water on slightly to identify leak and identified leak in valve system. Shut water back off and ordered replacement part. When part came, removed water line from assembly; moved electrical and water hose connections from existing part to new part one by one to be sure t they were in correct place. (To remove water lines, push o ring toward the assembly and pull hose out. To put into new bracket, merely slide in and they will lock in place) Fasten water line on new part using teflon tape. Turn on water slowly to check for leaks. Attach back to fridge and replace shield. VERY EASY!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsWrench(Adjustable)

CustomerGilbert from Tucker GA

Leaking inlet water valve

Disconect and Removed cover from back of frig.
Removed water supply pipe (adjustable wrench).
Removed Bracket and Valve Assembly from frig (1 screw).
Marked tube placements with marker so that I could put them back correctly.
Removed power connectors from valve.
Disconected tubes from valve (not that easy to pull off).
Connect tubes on new valve. Plug power connectors back in.
Screw the Assembly back on the frig.
Reconnect water supply & test for leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerJudy from Lenzburg IL

Ice maker stopped producing ice

I determined that the icemaker was not getting any water to the unit. The icemaker was still cycling but was not filling with water. I assumed the water valve was malfunctioning so I looked up the schematic drawing on the site and ordered the Water Valve & Bracket Assembly. It arrived within days. It took less than 10 minutes to install with miniumal effort. Within minutes the water could be heard flowing into the unit. Within an hour we had ice again!!!!!!!!!!!!!!!!!!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 12 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerNathan from Portage MI

Water inlet to icemaker freezes up.

Removed the back panel from the lower part of the fridge to expose the valves and motor. Then the one screw holding the valve/bracket assembly was removed to free the assy. It took a few minutes to figure out how to remove the water lines - popped the colored plastic rings out with a screwdriver and removed the lines. Inserted the lines one by one as they were removed to keep correct orientation. Removed the two electrical connections and plugged into new valve. Installed assy with the one screw. Replaced back panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerErnest from Fleming Island FL

Solinoid valve body started leeaking

Took back plate off of unit, shut off water, cut and marked water lines after unpluging wire harness, replaced unit

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerJohn from Long Beach CA

Water valve was slowly leaking onto hardwood floor

I removed the one screw from the bracket that held the entire assembly in place. I then transferred the electrical connections and water lines one at a time from the old part to the new one so as not to mix them up. I reconnected the water line with the use of some plumbers tape. I turned the water supply back on to check for leaks. After not finding any, I placed the completed assembly back inside the refrigerator, screwed the bracket back into place, and I was done. Incredibly simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsWrench set

CustomerThomas from Venice FL

Leaking water control valve

Unplugged electrical and turned off water at source. Removed back cover of refrigerator. Removed one bracket screw holding water valve. Pulled element out six to nine inches and disconnected water line to the unit. Removed electrical and water lines from old valve. Marked each line for easy reassembly of new valve. Turned water back on and tested for leaks. The whole process was very easy. Service from PartSelect .com was very good.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsWrench(Adjustable)

CustomerDoyle from Richmond VA

Water was dripping from the rear of refrigerator.

I removed the nuts holding the cover to the back of the refrigerator.
I removed the main water line to the part.
I then removed the nut holding the old water and valve bracket assembly to the refrigerator.
I removed the wiring harness from the old part and attached it to the new one.
I pressed down on the release to the hoses, pulled them out, and reattached them to the new part.
I reattached the part to the refrigerator.
I reattached the main water line back to the part.
I reattached the cover to the back of the fridge.
I tested the icemaker and water dispenser--and everything worked fine.
And, the best thing was, there was no puddle of water at my feet! Such an easy fix!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerRobert from Bayside NY

Leaky water valve

1) Shut off water supply
2) Pull out Refrigerator
3) Unplug
4) Unscrew back panel
5) Remove main water supply line
6) Remove bracket
7) Cut supply hoses 1 at a time and insert in new assembly in correponding openings
8) Reverse steps and enjoy

Notes: Judging by the new part's look, I suspect this repair will be needed again in about the same amount of time (5 years). The incoming pressure (I live in NYC) is probably too much for the way the part is built. Fortunately, now I know where to look , what to order and where to get it (great service, partselect.com!) it's no more then a 15 minute job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench set

CustomerJune from Forney TX

Leaky water valve assembly

Turned off the water and unplugged the frig. Removed the assembly (the hard part as it was corrodided) by removing 4 screws and slipping the electrical connections off. The water lines slipped off easilyThe instructions were good and the part fit easily. Then reversed the process by connecting the electrical and water.
I ordered the part via internet on Wed. evening and received it on Friday. Excellant service!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerCHARLES J from AURORA CO

Water valve was leaking!

The defective solenoid assembly was removed from the refrigerator and the electrical connection was unplugged. The new assembly was placed beside the defective part so the wiring harness could be removed and installed on the new assembly. I had to use a flat screwdriver to loosen the connectors. The water connections were then carefully moved, one at a time, to the new valve. The water was then turned on to check for leaks. There were none so the assembly was installed in the refrigerator and the back cover was screwed into place.

The part was shipped on a Monday and I received it at noon the following Tuesday, using the least expensive shipping method!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Valve and Bracket Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerwanda from fredericksburg VA

Water dispensor leak

The water dispenser on my GE refrig started leaking for about 5 seconds after release of the switch. I replaced the filter and the combination ice/water solenoids. Though this did not solve my problem I did troubleshoot more. I located the water reservoir behind the vegetable drawer. The reservoir mount had broken off. The reservoir had flipped so the water connection was no longer at the top. This was the cause for the continual leak. After mounting the reservoir correctly, the water leak stopped.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 38