298353-1-S-GE-WR2X7054          -Push On Nut
298353-1-S-GE-WR2X7054          -Push On Nut 298353-2-S-GE-WR2X7054          -Push On Nut

Push On Nut

PartSelect Number PS298353

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $3.35
  • You Save

    $.56
  • Your Price

    $2.79
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 20 reviews What's this?
16-20 of 20
 

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerGeorge from Salem VA

The drain shaft seal was leaking.

The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerEric from Altaville CA

Water leak around the drain valve shaft.

Ordered the Drain Valve Shaft Seal and Push On Nut to make repair. Removed dishwasher from counter. Removed motor/pump assembly from dishwasher. Removed drain celenoid from pump. Removed old push on nut and old drain valve seal. Installed new seal and push nut. Replaced everything in reverse order. Amazingly no water leaks after reinstallation. Seams to be working fine so far....fingers crossed. Hoping to get a few more years out of this dishwasher.
Thank You PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDean from Lincoln University PA

Leak at bottom of dishwasher on drain valve

Small rubber gasket needed to be replaced. Not the best design by GE, but it has lasted 11 years before leaking.
Needed to remove the solenoid to access the shaft of the valve. Tough to push gasket into place, but eventually it fit in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerSteve from Clearwater FL

Water leaking from dump valve area when draining

I ordered a drain valve shaft seal and new push on nut after reading similar stories of leaking problems on-line. I was pretty sure the leak was coming from the dump valve seal.

With repair parts on-hand, I took my dishwasher out during kitchen remodeling. I put the dishwasher on it's left side and removed the solenoid rod (lifts out on its own) and the dump valve's white plastic lever. I removed the old push on nut and pulled out the old washer with a small screwdriver. I then installed the new washer paying close attention to the supplied directions that said to install it with the lip in the correct direction. I then slipped on the new push on nut. The new push on nut is necessary since the old one will be destroyed in trying to remove it. I attacked it with needle nose plyers, a nail, and a small screwdriver before getting it bend and become loose enough to slide off. Care must be taken not to damage the shaft and groove. If you are generally handy at repairs, this repair will be easy.

I just hooked it up a few days ago and ran a cycle and no leak. Countertops will be installed in 4 days and the dishwasher will then get used frequently. I have faith the repair will hold and the dishwasher will remain leak free.

Luckily PartSelect was available to order the $20 repair parts and keep my faithful dishwasher on-line. Saved me the cost of a new $500 unit. I know this dishwasher cleans well and I don't have to risk buying a new one just to find out it doesn't clean as well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerFrank from St Louis MO

Water leak

Removed 1 C clip and 2 screws that held the Solonoid, cut the old push on nut off with a pair of dykes so it would not scratch the shaft, pinched out the old seal with a needle nose pliers and wiped everything clean with a moist paper towel. Replaced the old parts with the new ones but I still have the same, smaller, but same water leak.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-20 of 20